Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
23rd March 2007, 09:13 AM #1New Member
- Join Date
- Mar 2007
- Location
- England
- Posts
- 4
'shiny mark' on laminate kitchen worktop left by a pencil rubber!
Hi, I have a laminate kitchen worktop, made by wilsonart, it’s called ebony star, I drew a line on the laminate side with a pencil and then rubbed it out with a pencil rubber and now the rubbed out area has left what I can best describe as a 'shiny mark' that stands out against the rest of the laminate worktop.
I created that mark again on a spare piece of the same worktop and I have used the following below to try and remove this ‘shiny mark’ but I have had no success, can anyone please help me with any advice?
Products I have used already: windowlene window cleaner, mr sheen polish, cif, flash, white spirit, nail varnish remover which contains acetone, wood and laminate tough wipes, dettol surface cleaner.
<!-- / message -->
-
23rd March 2007 09:13 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
23rd March 2007, 09:22 AM #2
I doubt that you can remove the mark, sorry to say. The matte effect in the laminate is achieved by using a surface texture by incorporating silica flatting agents in the surface finish. By rubbing with the rubber you have removed the tiny peaks that stick out of the surface. The same thing will happen to a matte varnish coating etc.
Over time most matte surfaces "gloss up" with use and abrasion.
You can always contact Wilson to see what their recommendation is.
-
23rd March 2007, 07:04 PM #3Senior Member
- Join Date
- Oct 2006
- Location
- perth
- Posts
- 270
HI all
Try - tooth paste / creme cleanser - they are both mildly abrasive and may take the shine off.
Celeste
-
23rd March 2007, 10:05 PM #4
oh oooohhhh.
I find myself cutting sink holes and stove tops into this texture of benchtop from Wilson art. With your sander, scuff the surface and relaminate with some new laminate using red anchor glue. I'll get you some. Why is it a problem having these marks?. You've not made it clear. Have I missed something?
-
24th March 2007, 12:47 AM #5New Member
- Join Date
- Mar 2007
- Location
- England
- Posts
- 4
-
24th March 2007, 12:49 AM #6New Member
- Join Date
- Mar 2007
- Location
- England
- Posts
- 4
-
24th March 2007, 12:55 AM #7New Member
- Join Date
- Mar 2007
- Location
- England
- Posts
- 4
-
24th March 2007, 10:52 AM #8
oooops
Ooops Is this top in your kit? oops I thought you meant a kit bench top in your work shop. hhee hhee Hence my usless advice. Hows the weather in Sussex?
Cheers Tony
-
24th March 2007, 11:19 AM #9
Are you sure it was a pencil rubber and not a pen/ink rubber? Pen/ink rubbers have an abrasive in them which will have a buffing/cutting effect on the laminate....leaving a shiny area.
Using any kind of cleaner with an abrasive in it, or any cream/liquid that feels like it has a fine grit in it like 'Jiff' will act as a buffing compound on the laminate and leave a shine on the laminate.
Only thing I can suggest if what I described above has happened, is to get a fine grit like 800-1200grit paper and carefully try and dull down only the shiny area........practice many times on a scrap piece.I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones.
Albert Einstein