Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Spanner for TSC 10HB
-
30th March 2011, 12:32 PM #1SENIOR MEMBER
- Join Date
- Jun 2009
- Location
- Elizabeth Bay / Oberon NSW
- Age
- 76
- Posts
- 934
Spanner for TSC 10HB
I am missing a spanner for my TSC 10HB Carba-Tec table saw and they have none in stock. It's to hold the flange from slipping when I replace the blade. The spanner size needs to be 29mm to fit the slots cut into the flange. Maximum thicknesss 6.5 mm.
Is anyone else using a standard spanner I could buy?
I am sure it would be one made from metal plate because all the forged tools are too thick at the business end. Otherwise I'll have to make one from Al plate.
Mick
-
30th March 2011 12:32 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
30th March 2011, 02:37 PM #2
I have a 10HB and have always only used a spanner to tighten the nut. The blade have never come off in 5 years. I don't recall ever receiving such a spanner that you describe. Maybe my model does not need it. I just hold onto the blade with a rag to prevent cuts to the hand when loosening or tightening the nut.
Regards
Les
-
30th March 2011, 03:05 PM #3Senior Member
- Join Date
- Sep 2003
- Location
- Albury NSW
- Age
- 80
- Posts
- 104
Tsc 10hb
I also have the TSC 10HB but I have never used the thin spanner that came with it to change the blade. A piece of softwood under the blade holds it perfectly securely while tightening the nut with a large ring spanner. Same for removing the blade.
Jim Grant
-
30th March 2011, 03:45 PM #4
just as well I am thick ..... I think?
-
30th March 2011, 04:44 PM #5SENIOR MEMBER
- Join Date
- Jun 2009
- Location
- Elizabeth Bay / Oberon NSW
- Age
- 76
- Posts
- 934
Thanks Les & Jim,
I have been using the towel method as well until I had a blade in yesterday which just didn't want to grab the flange. That's the first time it has happened to me. Anyway, I went for the multi-grips but put a gouge or two in the flange along the way. No real drama but a spanner would have been a bit easier.
Mick
-
30th March 2011, 05:22 PM #6
Hi,
Can't you get hold of a cheep second hand spanner and grind the sides down on a bench grinder?
May be easier than making a whole spanner.
RegardsHugh
Enough is enough, more than enough is too much.
-
30th March 2011, 05:43 PM #7
The only spanner you need is the one for the nut, the one on the backing flange is for maintance.
There is no need for the nut to be done up using two spanners, the arbor thread is designed to tighten with little effort. Holding the blade by hand and using the spanner on the nut until the blade starts to bite into your skin is tight enough.
The only time you should use a tool for this is if you have medical problems with your grip.....................................................................
-
30th March 2011, 07:15 PM #8Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
Whilst you only need one spanner for the nut it is much kinder on your hands with the two spanners, one for the nut and one for on the motor side.
I made one by grinding an old steel spanner to size and changing blades is much easier.
Peter.
Similar Threads
-
NT 30 spindle spanner
By Dave J in forum METALWORK FORUMReplies: 26Last Post: 27th September 2012, 06:22 PM -
Spanner query
By Gomez in forum HAND TOOLS - UNPOWEREDReplies: 13Last Post: 16th March 2011, 11:22 PM -
Spline Spanner
By Sterob in forum METALWORK FORUMReplies: 7Last Post: 18th September 2007, 08:01 PM -
I left the Spanner in the Van
By Wayne Davy in forum NON WOODWORKReplies: 2Last Post: 12th May 2003, 10:31 AM