Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 3 of 3
Thread: How square is square?
-
2nd April 2020, 12:34 PM #1SENIOR MEMBER
- Join Date
- Jun 2009
- Location
- Elizabeth Bay / Oberon NSW
- Age
- 76
- Posts
- 934
How square is square?
I have a veneered panel of 12 mm ply and 2.5mm of Hoop Pine measuring 1126 x 579. When laying the veneer before pressing I neglected to square it up perfectly with the plywood sheet. Lesson learned. By making a jig for the table saw which would use the edge of the veneer as a guide, I managed to get the long sides parallel but not owning a panel saw, found it impossible to square up the shorter ends accurately.
Veneered Hoop Pine panel.jpg
The diagonals revealed I was off 5mm. After a lot of hand planing and checking for square and straight edges, I've now arrived at a 2mm difference. 1263 versus 1265.
The panel is destined to be a desk top, framed by 10mm of Toona and then 50mm of Silky Oak all with mitred corners.
Is this good enough? Or should I go for perfect? Not simply for perfection's sake but will I have problems later with the joinery?
mick
-
2nd April 2020 12:34 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
2nd April 2020, 01:35 PM #2SENIOR MEMBER
- Join Date
- Oct 2010
- Location
- NSW
- Posts
- 643
It'll be plenty good enough Mick. 1mm across the diagonals of the top will amount to 9/10 of #*!^ all in you frame mitres.
Cheers John
-
2nd April 2020, 01:55 PM #3rrich Guest
I had asked the same question and Rob Johnstone offered a brilliant suggestion.
Lets get our good friend Pythagoras involved. And then a router. Actually brilliant when you think about it.
Remember the numbers 3, 4, 5 or any multiples. 30, 40, 50 ; 60, 80, 100
Put a straight bit in your router. Measure from the bit to the edge of the router. To that measurement add a skosh. Whatever number that you come up with, put a mark that far from the short edge on the long edge. On the long edge, measure (assuming 60, 80, 100) 80 Cm from the first mark and put a mark.
Take a compass, expanded to 60 Cm, and from the first mark, swing an arc in an area that would be approximately 90° from the mark on the long edge. Expand the compass to 100 Cm and from the other mark on the long edge and swing an arc crossing the first arc. You now have two points of a line that is at a right angle to the long edge. From the first mark through the crossing of the two arcs. Clamp a fence along that line as a router guide. Use your router and straight bit to square up the large sheet.
Similar Threads
-
square cuts with the blade at 90, out of square at 45???
By zoovegroover in forum WOODWORK - GENERALReplies: 3Last Post: 9th July 2017, 07:54 PM -
Sliding miter saw: how square is square?
By IdahoEv in forum GENERAL & SMALL MACHINERYReplies: 12Last Post: 21st April 2016, 05:14 AM -
Installing vice: how square is square?
By tomnewby in forum WOODWORK - GENERALReplies: 12Last Post: 27th June 2009, 08:03 AM -
square to table or square to fence
By yjnb in forum BANDSAWSReplies: 1Last Post: 20th July 2008, 07:50 AM