Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: Steam bend.
-
17th February 2007, 08:18 PM #1
Steam bend.
Has anyone got designs for a steaming chamber? My 1st effort failed to generate enough heat.
Cheers Tony.
-
17th February 2007 08:18 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
17th February 2007, 08:21 PM #2Registered
- Join Date
- Aug 2003
- Location
- .
- Posts
- 10,482
Have look here.
https://www.woodworkforums.com/search...archid=1247116
Al
-
17th February 2007, 10:13 PM #3
I have, but I wan't to see Al's thread work first so that I'm not doubling up.
Regards,
Noel
-
17th February 2007, 10:21 PM #4
So as we don't get all confused......it is after 9 PM...go up the top of the page to the search area........highlight the woodworking forums bit....type in steam bending...then stand back. Every post from the forum on steam bending comes up.
If you need more info after you've read all that then give us another yell.
Regards,
Noel
-
18th February 2007, 07:58 AM #5Registered
- Join Date
- Aug 2003
- Location
- .
- Posts
- 10,482
Thanks Noel.
The link didnt work for some reason??
Al
-
18th February 2007, 08:05 AM #6
Mornin"
The link gives me a Vbulletin Message
"Sorry - no matches. Please try some different terms."
????
Regards,
Noel
-
18th February 2007, 08:07 AM #7Member
- Join Date
- Sep 2005
- Location
- Kent UK
- Posts
- 68
this lot might help, there are photos on the thrid or fourth page
hope the link works
-
18th February 2007, 08:08 AM #8Member
- Join Date
- Sep 2005
- Location
- Kent UK
- Posts
- 68
lets hope it works in the clear http://www.trustedtradesmen.com/foru...?TID=9430&PN=2
-
18th February 2007, 08:10 AM #9Member
- Join Date
- Sep 2005
- Location
- Kent UK
- Posts
- 68
thank goodness the link works in the clear
-
18th February 2007, 12:09 PM #10
steamer plans
Ozwinner And Watson Thankyou both.
Mr Watson sir. If I may when you might be able, I would be rapt to have some of your plans. I thankyou. Hmm... will I buy my 60 acres in mid Vic? Only 2 and a bit hrs from my beloved fishing paradise in Portland ha he
Is that tradepersons site you gave me a good one? Should I reg? Is It an Australian based one?
Oh yeah and not forgetting the plans ha he . Thanks both of you.
Tony.
-
18th February 2007, 12:26 PM #11
G'day Tony,
I'll bash the plans into shape and reduce them to a suitable size for posting here.
The best reference that I have is The Complete Manual of Wood Bending by Lon Schleining published by Linden Publishing.
I got my copy via Amazon.com.
Regards,
Noel
I think the Tradepersons site might be from the UKLast edited by watson; 18th February 2007 at 12:29 PM. Reason: Addition
-
18th February 2007, 03:25 PM #12
G'day Tony,
Here's a drawing of the plan I used. I've had three test runs, and on the third run I wacked in some pine and of course I cracked it during bending "cos I haven't built the compression straps yet.
It reaches between 87º C and 93º C ...don't know why the range?????
Points I learned from the book and used where:
Used formwork ply.......got it from the local tip.
Used a 240V Urn.........cost me a dollar at a clearing sale.
Used Polyurethane glue on all joints. No screws.....where I did use them they were removed when the glue set.
The door is a loose fit, with weather seal on the edges.
Bits I "thunked" up myself:
added the two 12V DC fans to move the steam around.
They are Item 33383 from www.rockby.com.au and cost $3.50 each.
They draw 200 milliamps each, and I powered them from a 12V 500milliamp plug pack mounted externally.
After each test run I removed them to see how much moisture had got in them. Couldn't shake any drops of water out of them....so I don't know how long they'll last.....don't care...bought 10 of 'em from Rockby.
Other point:
I only half filled the urn (water conscious) that's 12litres, and that took 25minutes to reach a rolling boil. The meat thermometer took 45 minutes from switch on to reach about 90ºC.
Hope that's of interest to you.
Regards,
Noel
Bugger.I've had an invalid file message when I tried to upload the drawing.
I'll send this to save typing all that again, and follow with a drawing.
-
18th February 2007, 03:41 PM #13
Try again
Similar Threads
-
Steam bending (again)
By Arron in forum WOODWORK - GENERALReplies: 40Last Post: 6th October 2011, 04:00 PM -
Has anyone successfully steam bent Jarrah?
By Ramps in forum TIMBERReplies: 24Last Post: 20th August 2006, 08:41 PM -
Laminating/steam bending
By Porky in forum WOODWORK - GENERALReplies: 9Last Post: 16th May 2006, 09:40 AM -
Steam bending yet again
By Arron in forum WOODWORK - GENERALReplies: 5Last Post: 19th March 2004, 11:22 AM -
Improving steam bending
By Arron in forum WOODWORK - GENERALReplies: 14Last Post: 5th February 2004, 09:03 AM