Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
-
24th February 2020, 05:34 PM #1GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 2,680
Wanted, someone that can steam bend Adelaide.
Wondering if anyone has the setup and would be willing to steam bend a bit of blackwood 10 x 165 x 540 which I can supply. Its for the insert of a highback dining chair similar to picture.
15825259703911056424950964931839.jpg
Willing to pay for your time and trouble.
-
24th February 2020 05:34 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
24th February 2020, 08:22 PM #2
dont know what part of town your in but chase up SANE Makerspace 3/6 Armiger court, Holden Hill ph 0433 372 578
privately owned community workshop, been going for a number of years any time I am in town I pay them a visit and grool at the setup they have.
yearsago young couple bought a camper van to tour Aus, needing new curtains...they bought a swing machine then found out they didnt know how to use it, so a visit to this place but oh dear time and dreams got away...6 months later they finally left on their journey, with new curtains, plus a complete new interior they did (mostly) themselves
dont know if Matt/Marc??? can help you...lets know the outcome pleaseI would love to grow my own food, but I can not find bacon seeds
-
24th February 2020, 08:33 PM #3GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 2,680
-
24th February 2020, 09:52 PM #4
The steaming would be the easy part, but you would need to fabricate the form to bend it over. I am aware of three ways to set up the form, a male and female pair that can clamp together sandwiching the steamed part, forcing it to take the required shape, a male form set up to take clamps and cauls about every 75mm to pull the steamed blank into the required shape, or a male form set up to be used with a vacuum bag, or with a thin metal strap under tension to force the blank into shape.
Since the chair back most likely has some reflex shape, the metal strap approach most likely will not work as it can only produce a curve in one direction. The vacuum bag approach would require a significant bag and pump, plus experience, to make it work. A male form and clamps and cauls should be able to do the job, but may result in curves in segments rather than smooth curves, which may be an issue if the blank is already at required thickness, as there is no meat left to smooth the ridges and generate a smooth curve.
The male female forms method would be the most difficult to create, as you need to create two forms that are offset by the blank thickness, and with a surface finish equivalent to what you hope to achieve in the finished article. One possibility would be to get your form surfaces as good as you can, then surface both with a strip of thin laminate (non textured) to provide the final smooth surface that the reflect in the completed part.
If at all possible, you need enough material left in the blank to allow a final sanding etc after steaming and forming as the wood may discolour or waterstain on the surface in the steamer, and need to have this corrected prior to inclusion in the chair.I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
-
24th February 2020, 10:31 PM #5
-
25th February 2020, 08:03 AM #6
That part of the chair you have wasn’t steam bent and if your building a similar thing I wouldn’t be steam bending it .
With that splat lying flat on a bench top measure from the bench to the highest part and you have roughly the thickness that would have been sawn from a board then sanded . And that thickness you get will nicely fit within one of the standard board thicknesses of either 1 1.5 or 2 inch with room for spoke shaving , scraping and sanding .
Just saying that’s the way Blackwood 20th century chairs with those sort of backs were mostly made .
Rob
-
25th February 2020, 09:32 AM #7GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 2,680
-
25th February 2020, 09:43 AM #8GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Adelaide
- Posts
- 2,680
-
25th February 2020, 04:19 PM #9
-
25th February 2020, 08:35 PM #10China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 4,475
I will third that, it's not steam bent
Similar Threads
-
hmmmm, pallet timber WON"T steam bend?
By fletty in forum WOODWORK - GENERALReplies: 35Last Post: 15th June 2015, 12:18 AM -
To laminate or to steam bend this project??
By mfarr in forum TIMBERReplies: 17Last Post: 19th November 2011, 08:23 AM -
got a Tight steam bend in some silky oak.
By JDarvall in forum WOODWORK - GENERALReplies: 61Last Post: 24th February 2010, 02:27 PM -
Steam bend, Glulam or both?
By Gumbatron in forum WOODWORK - GENERALReplies: 17Last Post: 3rd February 2008, 11:23 PM -
Steam bend.
By rgum in forum WOODWORK - GENERALReplies: 12Last Post: 18th February 2007, 03:41 PM