Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 6 of 6
  1. #1
    Join Date
    May 2012
    Location
    Brisbane (Chermside)
    Age
    71
    Posts
    2,076

    Default Steam Bending camphor laurel

    Can anyone help me understand how good or bad camphor is for steam bending?

    Bootle does not mention steam bending for camphor. I found precious little on the web, so here I am, asking for advice.

    Thanks,

    John

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Age
    2010
    Posts
    Many





     
  3. #2
    Join Date
    May 2009
    Location
    Coffs Coast
    Posts
    141

    Default

    Bloody awful. Grain runout means a nice big pile o kindling by the end of the day. Straight grain is critical. That is very rare in camphour.

  4. #3
    Join Date
    Apr 2005
    Location
    kyogle N.S.W
    Age
    50
    Posts
    4,844

    Default

    As all timbers bend. I think it depends on how much of a bend your after. I've made camphor bend just enough for what I wanted once.

    From my experience in some soft timbers, its not the runout thats the biggest problem, its its ability to compress evenly on the inside of the bend. ie. no compression failure. ie. visual compressed points on the inside of the bend. A compression failure in a soft timber can't be ignored.

  5. #4
    Join Date
    May 2012
    Location
    Brisbane (Chermside)
    Age
    71
    Posts
    2,076

    Default

    Thanks guys,

    I think my best bet is to build a steamer and test a couple of pieces.

    The good news is that I have some nice straight grained camphor laurel on hand. What I am doing is putting a twist of about 25-30 degrees in a board that will be the sides of the back of a chair, to allow for the bend in the back rest. So it is not a severe bend.

    I note on youtube that some blokes deliberately over-bend the wood a bit, then remove it from the former and put it in a frame that holds it in the finished shape as it dries. If that reduces spring-back, it sounds like a good idea.

    All will be revealed in the fullness of time.

    Cheerio!

    John

  6. #5
    Join Date
    Mar 2005
    Location
    Camden, NSW
    Age
    74
    Posts
    3,576

    Default

    Quote Originally Posted by John Samuel View Post
    Thanks guys,

    I think my best bet is to build a steamer and test a couple of pieces.
    Hi John, I've been trialling different timbers to steam bend over in the CHAIR DESIGN 101 thread so I threw in a couple of pieces of camphor laurel today to save you some grief!
    In short...
    • the cross section was 10 x 25 mm
    • steamed for an hour
    • bent in a fairly gentle double bend former
    • 15 minutes in bending former before ....
    • moved to drying former for an hour ... so far


    20140614_132216.jpg


    20140614_132153.jpg

    Results
    • bent easily
    • no cracking on compression nor tension sides (but it IS a small section?)
    • very pliable in the bend and I doubt twisting would be a problem

    fletty
    a rock is an obsolete tool ......... until you don’t have a hammer!

  7. #6
    Join Date
    May 2012
    Location
    Brisbane (Chermside)
    Age
    71
    Posts
    2,076

    Default

    Quote Originally Posted by fletty View Post
    Hi John, I've been trialling different timbers to steam bend over in the CHAIR DESIGN 101 thread so I threw in a couple of pieces of camphor laurel today to save you some grief!
    SNIP
    Results
    • bent easily
    • no cracking on compression nor tension sides (but it IS a small section?)
    • very pliable in the bend and I doubt twisting would be a problem

    fletty
    Thanks Fletty.

    I am a couple of weeks off doing my test chair, but those results are encouraging.

    Much appreciated!

    John

Similar Threads

  1. Steam bending (again)
    By Arron in forum WOODWORK - GENERAL
    Replies: 40
    Last Post: 6th October 2011, 04:00 PM
  2. Steam bending ply
    By pippa_21 in forum WOODWORK - GENERAL
    Replies: 9
    Last Post: 18th January 2008, 06:50 PM
  3. Steam bending
    By Bob Hall in forum WOODWORK - GENERAL
    Replies: 0
    Last Post: 18th September 2007, 06:08 PM
  4. Steam bending yet again
    By Arron in forum WOODWORK - GENERAL
    Replies: 5
    Last Post: 19th March 2004, 11:22 AM
  5. Steam bending.
    By RETIRED in forum TIMBER
    Replies: 5
    Last Post: 25th June 2001, 10:00 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •