Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
-
2nd January 2013, 01:36 PM #1New Member
- Join Date
- Jan 2011
- Location
- vic
- Posts
- 3
Straightening walls for plaster work
Is it OK to straighten walls for plastering before external brickwork is finished?
-
2nd January 2013 01:36 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd January 2013, 01:53 PM #2
Is that straightening by using the brick ties to pull the frames straight, or straightening by hitting studs with a planer/adding packing where needed???
-
2nd January 2013, 03:20 PM #3GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
There isnt much point in straightening until the job is weather proof. Rain, wind and sun will continue to cause timber movement, often making it necessary for the job to be done all over again. If you have a stud that is so bent it requires crippling from the brick side, then that would be much easier to do without bricks in the way. Otherwise do 'em later.
-
2nd January 2013, 04:13 PM #4SENIOR MEMBER
- Join Date
- Apr 2012
- Location
- tasmania
- Age
- 58
- Posts
- 116
Straightening walls for plaster work
As long as roofs on, windows are in and house is wrapped no problem
-
2nd January 2013, 05:07 PM #5SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 601
Don't try to pull the wall straight by using the bricks,the brick ties should be only there to tie the bricks to the wall.
As mentioned straighthen the internal wall studs after the building is weather proof.
-
2nd January 2013, 05:14 PM #6
...and you cannot cripple/cut external load bearing studs, replace them.
-
2nd January 2013, 06:34 PM #7GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
-
2nd January 2013, 06:36 PM #8
-
2nd January 2013, 07:23 PM #9Senior Member
- Join Date
- Jun 2012
- Location
- Mosgiel New Zealand
- Posts
- 221
Having been building all my working life as has been said dont do it till the place is right ready to line this includes the moisture content to your building standard then if the bricks are on srtaighten by planing and packing, if the bricks are not on you can cut and wedge with a block nailed beside to your local requirments,best you check with the localcouncil firts.
Ian
-
2nd January 2013, 08:21 PM #10
Maximum 2 consecutive studs allowable.
NO NOT straighten studs until all brickwork is complete.
NO NOT straighten studs until last brick laid is cured for 5 days
Nail off your brick ties (slope UPWARDS approx 10 to 15 degrees) at door studs, window studs and wall intersections first then use a straight edge or offset string line to straighten remainder between these. Standard galvanised clouts are NOT ALLOWED, use structural galvanised Teco or Pryda nails 2 per brick tie.
Ties can be used to straighten studs (in or out) providing it is no greater than 6mm.
Between 6mm and 10mm cut max 2/3 into stud, wedge if the bow is towards the brickwork, push and close saw kerf with skew nail if bow is away from brickwork.
In both instances, cleat each side of stud with 20mm thick timber extending min 600mm each side of cripple cut. The cripple cut should be in the middle of the length of the stud which may require replacing any noggins to allow for cleats. Cleats must have min 6 nails each side of cripple cut.
If the stud is bowed greater than 10mm, it must be replaced.The person who never made a mistake never made anything
Cheers
Ray
-
2nd January 2013, 09:08 PM #11New Member
- Join Date
- Jan 2011
- Location
- vic
- Posts
- 3
Appreciate! Thanks guys.
Similar Threads
-
Wall plugs, Plaster, Timber, Masonry.
By Mychael in forum WOODWORK - GENERALReplies: 6Last Post: 20th April 2011, 11:31 PM -
Straightening lead screw
By Fossil in forum METALWORK FORUMReplies: 17Last Post: 12th June 2008, 09:39 AM -
Straightening out a compass saw blade
By Green Woodchips in forum HAND TOOLS - UNPOWEREDReplies: 2Last Post: 20th July 2005, 05:01 PM -
Straightening a small warp
By zundfolge in forum WOODWORK - GENERALReplies: 7Last Post: 31st May 2005, 08:32 PM