Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Supermax open ended drum sander
-
7th June 2018, 09:48 AM #1GOLD MEMBER
- Join Date
- May 2009
- Location
- melb
- Posts
- 1,125
Supermax open ended drum sander
Anyone own a supermax open ended drum sander? How is it going? does the drum stay pretty parallel to base?
Do you have open or closed base? Apart from storage is one better than the other?
Ever have issues with the entire machine tipping when putting through large work pieces? (I am thinking about getting the 25-50)
What grits do you generally stock? Would you recommend starting with 40 (or lower?) if you are trying to flatten something (such as epoxy filled gum veins or a live edge slab you cannot fit through thicknesser)
Is it powerful enough? I notice theyre all single phase, if doing 40grit passes will it stall?
-
7th June 2018 09:48 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
7th June 2018, 04:02 PM #2rrich Guest
I would think that the sander is a smoothing device and not a thicknessing device.
-
7th June 2018, 05:18 PM #3GOLD MEMBER
- Join Date
- May 2009
- Location
- melb
- Posts
- 1,125
I just purchased a new thicknesser so will be using that when possible. but its very time consuming sanding epoxy flush to the timber if there is a lot so would rather not do that by hand. As for the slabs, I would imagine that after using router sled its not going to be perfectly flat (just based on what I've seen on utube) so would rather do a few passes through sander
-
7th June 2018, 06:06 PM #4SENIOR MEMBER
- Join Date
- Jul 2009
- Location
- inverloch
- Posts
- 472
I own the 19-38 and am very happy with it. I am mostly doing smaller stuff but recently sanded a 2100x900 door without any trouble. The drum stays parallel OK after the initial set up adjustment and the lever works very well to adjust the conveyer if sanding wider than 19".
I have the open stand which works well for me and I also use in feed and out feed stands so tipping is not a problem.
I have found powerful enough but I have not gone lower than 80 grit but the idea is not to take great chunks off but to wind it down no more than a 1/4 turn at a time (about 0.4mm). In any event the so called "Intellisand" feature is supposed to compensate for too big a bite.
I use 80, 120, and 150 grits
-
8th June 2018, 05:45 PM #5
I think mine is an old carbatec, can't remember. I don't use it often but when I do I use it a LOT. They are sometimes used to thickness accoustic guitar body bits. Set up and used carefully they can be very accurate. As said 40 grit is fine just don't try and cut too deep. That's not how it's supposed to be used. I've got a jointer/thicknesser. They are different tools to do different jobs. You might consider a router sled instead ?
I'm just a startled bunny in the headlights of life. L.J. Young.
We live in a free country. We have freedom of choice. You can choose to agree with me, or you can choose to be wrong.
Wait! No one told you your government was a sitcom?
-
8th June 2018, 07:54 PM #6GOLD MEMBER
- Join Date
- May 2011
- Location
- Murray Bridge SA
- Posts
- 3,339
If having to use 40 grit as a starter, you're asking way too much of the machine, it is after all a sanding machine, not a thicknesser, as others have mentioned. If you need to take down a lot of resin etc. I'd be looking to use a belt sander, or as someone else suggested a router sled to get off the worst of it.
KrynTo grow old is mandatory, growing up is optional.
Similar Threads
-
Carba-Tec 635mm Wide Drum Sander - Single Drum
By macka75 in forum HAND TOOLS - POWEREDReplies: 6Last Post: 28th October 2021, 10:00 PM -
Looking for someone with a Wide thicknesser / drum sander / belt sander In Adelaide?
By swiftden in forum WOODWORK - GENERALReplies: 10Last Post: 3rd June 2021, 03:35 PM -
Performax Supermax drum sanders
By ClintO in forum GENERAL & SMALL MACHINERYReplies: 3Last Post: 15th July 2012, 04:57 PM -
Balancing and truing Drum for Drum Sander
By Stetwood in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 11Last Post: 27th May 2007, 11:12 PM