Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Table Height
-
7th November 2005, 09:23 PM #1
Table Height
Can anyone tell me whether there is a standard height for tables (Dinner tables) and chairs................. I have a table here that is 770mm high and I reckon that it should be 700mm BTW I bought it like that.............. The saw's gunna come out!
Catch ya later,
Peter B.
(Corunetes)
--------------------------
You, you and you, panic!..... The rest of you come with me!
-
7th November 2005 09:23 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
7th November 2005, 10:05 PM #2
I think 33 - 36 inches is about the standard height but would depend on the chairs which you have - elbows should be able to rest easily on tabletop at about 90 degrees while seated.
-
7th November 2005, 10:34 PM #3
I thought it was 29" to 30", elbows do depend a bit on a persons height.
John
-
7th November 2005, 10:52 PM #4Awaiting Email Confirmation
- Join Date
- Aug 2004
- Location
- Melbourne
- Age
- 57
- Posts
- 49
I don’t think there is a “define” standard height for Dining room tables. Most Older table where usually made to a height of 29 – 29.5 inches.
Most tables to day vary from 29 –33”. I personally don’t go over 32” and will adjust the height to the depth of the rail and to customers requirements
I wouldn’t go as far as 36” (914mm) as this would be like sitting in your dining chair and eating from your kitchen bench top.
Chairs finish at a seat height of 18-19
Hope this helps
-
8th November 2005, 07:30 PM #5
The trade standard was 920mm for a sink bench and 765mm for a dining table with adjustments where necessary for individual use.
Rhys H.
-
8th November 2005, 10:12 PM #6
The height of the table surface is not important it is the relationship between the seat height of the chair and the eating surface paying careful attention to the clearance between the seat and the underside of table or frame leaving room for legs . I never build tables with supporting skirts for this reason. Of course my theory falls down if you are using the table for something other than eating and therefore require the "Work Surface" at waist height!!!.
RossRoss"All government in essence," says Emerson, "is tyranny." It matters not whether it is government by divine right or majority rule. In every instance its aim is the absolute subordination of the individual.
-
8th November 2005, 10:37 PM #7
A lot of old tables are about 75cm (30") high while modern tables are often about 70cm (28") high. These heights suit most chairs.
Sorry, but to suggest a dinner table should be 36" (90cm) high is nonsense. That's the standard height for kitchen benches.Rusty
-
9th November 2005, 10:48 AM #8
I believe 29" is the correct figure.
-
9th November 2005, 01:37 PM #9harcx
- Join Date
- Sep 2005
- Location
- Sydney
- Posts
- 81
Originally Posted by Corunetes
The industry start point we use is 720 (dont ask me what that is in Fahrenheight). We sometimes vary that down if it is to go in a small room as this can make the room seem a bit bigger
Useless piece of information
The cabin furniture on the original Queen Mary was scaled down (sometimes to 5/8 scale) to make the Cabins look bigger
Cheers
HarcX
-
9th November 2005, 04:47 PM #10
Ok the..... from the answers received I suppose that I will have to cut it down to 720centifeet or 29.6inchametres................ Ah. Now thats just being snide......... I'll do the deed to comfortable elbow height i think.... Thanx for the replies.............
Catch ya later,
Peter B.
(Corunetes)
--------------------------
You, you and you, panic!..... The rest of you come with me!
-
10th November 2005, 08:54 AM #11SENIOR MEMBER
- Join Date
- Jul 2003
- Location
- Melbourne
- Age
- 53
- Posts
- 856
Hi Peter, I am jumping in a bit late but lastnight I was reading an older issue of finewoodworking and they a 2-3 page article on Table sizing:
TABLE DESIGN
by Graham Blackburn
A well-proportioned table balances ergonomics with style
Its was in the MAY/JUNE 2005 (#177) issue, might worth checking it out if you have access to a copy.
Joe
Similar Threads
-
Modifying the Triton Router Table top height
By Ian Smith in forum TRITON / GMCReplies: 15Last Post: 14th October 2011, 07:24 PM -
Sliding extension table - out-of-square cuts
By Swagman in forum TRITON / GMCReplies: 3Last Post: 31st July 2005, 08:34 PM -
Bandsaw Table
By DPB in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 5Last Post: 25th March 2004, 01:21 PM -
Table Height in Crosscut mode
By Gumby in forum TRITON / GMCReplies: 9Last Post: 11th March 2004, 01:22 PM -
Over head Router over head height winding for Triton router table?
By Maxi in forum TRITON / GMCReplies: 5Last Post: 5th November 2002, 09:09 AM