Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: table leaf supports
-
27th September 2004, 11:02 PM #1
table leaf supports
Hi Everybody,
Could any one give me advice as to where I could get supports that will
hold the leaves up that I have attached to each end of my dining table. :confused:
The leaves are 260x740x20ml, not very big, but enables me to seat 6 friends if need be.
I made some 90 degree brackets which could hinge into the centre when not in use, but they get in the way when I drop the leaf down, I'm sure there must be some sort of metal support which would be hinged in the middle and
fold up to let the leaves drop down when I don't need them.
Anyway if anyone can suggest anything, I would be grateful.
ThanksThe Blonde
-
27th September 2004 11:02 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
28th September 2004, 08:07 AM #2Registered
- Join Date
- Aug 2003
- Location
- .
- Posts
- 10,482
HI
Why not add some timber rails that slide in and out underneath the table top.
They wouldnt be too hard to do, but you will have to remove the table top to fit them.
Al
-
28th September 2004, 12:10 PM #3Senior Member
- Join Date
- Apr 2004
- Location
- United States
- Posts
- 317
You can make swing out legs like a gate leg table. You can have slide out support like an old desk lid support or have some hardware that attaches to the apron and the dropleaf. Any of these might be a solution based on your table.
-
28th September 2004, 10:27 PM #4
table leaf supports
Thanks guys for the advice re leaf supports. I might give the swing out legs a try hcbph. They might be the easiest things to source. I dunno if I want to hack into the table too much ozwinner, I bought it as a kit form, very pleased with it, but might weaken it pulling it apart.
Thanks again
Catch yaThe Blonde
-
8th October 2004, 02:19 PM #5
Try something like this:
http://www.rockler.com/ecom7/product...d=462&catid=82In the beginning the Universe was created.
This has made a lot of people very angry and been widely regarded as a bad move.
- Douglas Adams
Guns are bad, mmmmkay.
-
8th October 2004, 09:11 PM #6
I agree with ozwinner, though it may sound like hacking it sure isnt - the finest tables I have seen used this method very successfully - having said this, when yuou say the table is a kit, I would be keen to see the construction of it and the added leaves you have made just to make sure ..... havent got time tonight to do a drawing of how the sliders work, sorry but will try over the weekend if youre interested
good luck with it
ps. by the way, where do you store the extra leaves when not required? May have some ideas regarding storage under the table top .....Steve
Kilmore (Melbourne-ish)
Australia
....catchy phrase here
-
8th October 2004, 09:26 PM #7GOLD MEMBER
- Join Date
- Jun 2003
- Location
- Sunbury, Vic
- Age
- 84
- Posts
- 2,719
There was a thread with diagrams on the sliding rail system on here a few months ago.
Try a searchTom
"It's good enough" is low aim
-
6th December 2005, 06:59 AM #8Senior Member
- Join Date
- Mar 2004
- Age
- 76
- Posts
- 188
Originally Posted by seriph1
My dining table, purchased new about 30 years ago, has a loose fitted top which lifts up to allow for extensions at either end to pull out. No fittings - it's all in the framing. The design allows for one or both ends to be extended. I can post a drawing if anyone is interested.
-
6th December 2005, 12:07 PM #9
very interested!
Thanks!Steve
Kilmore (Melbourne-ish)
Australia
....catchy phrase here