Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: small tape measure
-
22nd June 2014, 04:13 PM #1
small tape measure
I went to Bunnings this morning. I don't know why, they never seem to have what I want, but for some reason I keep going there. I must be a masochist or something. I should just stay home and bang my head against the brick wall.
Anyway on the way out I found a palletload of these sitting by the registers:
IMG149 (800x600).jpg
I thought for the sake of $4.50 (the 50c piece is the change, not part of the purchase) I will take one home. its 2m long and that's the part of the longer measures that you tend to use more than 90% of the time and it fits in my pocket without trying to pull my pants down.
The quality seems to be there but it is a bit tight pulling out the last 200mm of tape, possibly as a result of trying to make it as small as possible.
This was at Bunnings Hoppers Crossing but I would expect that all stores would have them.
(usual disclaimer: I do not work for bunnings and never will and have no other affinity with them except as a (usually disgruntled) customer)
Cheers
DougI'm doing my May Challenge - I may or may not give a #*c&
-
22nd June 2014 04:13 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
22nd June 2014, 05:38 PM #2
Yep the smaller tape measure is a good idea.
And made by a very strong and well established company.
-
22nd June 2014, 07:36 PM #3
Hi Doug,
Just make sure it's not an Imperial or Logarithmic 2 metre tape. That could be why they were cheap.
Regards,
Rob
-
22nd June 2014, 07:44 PM #4
-
26th June 2014, 01:51 PM #5rrich Guest
There are people here that would kill for an Imperial one.
-
26th June 2014, 07:13 PM #6
I got one about 2 or 3 months ago - Qld must get the deliveries from China sooner..
I've had small key-ring tapes for many years, they seem to pop up on counters and near checkouts in hardware stores from time to time. This tape is a bit bulkier than the last one (which is no use because the plastic eye wore through ), but it's 2M, & the old one was only 1M, so I guess it's swings & roundabouts....
Cheers,IW
-
27th June 2014, 09:01 PM #7GOLD MEMBER
- Join Date
- Aug 2005
- Location
- Queensland
- Posts
- 2,947
Could I make a suggestion……...
Take a board of known measurement [using your usual measuring tools].
Mark the board at set intervals e.g., 100mm, 250mm, 400mm etc.
Then check it with the new tape, rule etc.
I have been caught out with cheapies before - the measurements either intervals or overall or both will be different.
Unfortunately I have found discrepancies of up to 10mm. May not seem like much but if you are short/long when building something special it can be a PIA.
I learned a long time ago to ensure I used the same tape/rule for all measurements or if I had to use different measuring tools to have at least calibrated them together first - even the same brands are not immune of this problem e.g. a 5m and 8m tape or a 300mm and 1m steel rule from the same manufacturer.
Check out your measuring tools.
Similar Threads
-
Table Saw - Tape Measure
By Arry in forum WOODWORK - GENERALReplies: 3Last Post: 27th October 2009, 08:27 AM -
Self Adhesive Tape Measure
By grimmers in forum WOODWORK - GENERALReplies: 12Last Post: 3rd August 2009, 11:48 AM -
Tape measure clip
By bpj1968 in forum HINTS & TIPSReplies: 1Last Post: 12th September 2008, 03:26 PM -
Tape Measure
By Howdya do that in forum WOODWORK - GENERALReplies: 15Last Post: 1st February 2007, 10:27 PM -
Tape measure idea ????
By JDarvall in forum HAND TOOLS - UNPOWEREDReplies: 31Last Post: 7th September 2006, 09:50 PM