Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 17
Thread: Wax coating on wood
-
3rd September 2007, 02:27 PM #1New Member
- Join Date
- Sep 2007
- Location
- Rockville, MD
- Posts
- 3
Wax coating on wood
Hello all,
I am rekindling my love of woodworking and have a question that mostly likely has a simple answer. I purchased some small billets of exotic wood that has a protective coating of wax. What is the easiest way to remove? If I try sanding it clogs immediately. Any suggestions? Thanks for the help.
Rich
-
3rd September 2007 02:27 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
3rd September 2007, 02:31 PM #2
Pour a jug of boiling water over it to melt it off.
"... it is better to succeed in originality than to fail in imitation" (Herman Melville's letters)
-
3rd September 2007, 02:42 PM #3New Member
- Join Date
- Sep 2007
- Location
- Rockville, MD
- Posts
- 3
Thanks Claire.
Will that have any adverse affect? Some of these are exotic and some are burls, and one bird's eye maple.
-
3rd September 2007, 02:50 PM #4I may not have gone where I intended to go, but I think I have ended up where I needed to be.
My Other Toys
-
3rd September 2007, 02:56 PM #5New Member
- Join Date
- Sep 2007
- Location
- Rockville, MD
- Posts
- 3
Thanks. I just don't want to cause more problems by solving one!
Rich
-
4th September 2007, 12:43 AM #6
I'd suggest scraping instead. Boiling water could create quite a mess, especially as you probably don't know what kind of wax it is. In lieu of real scrapers ($$$), I use utility knife blades; scrape with the grain, and reverse the blade presentation when a burr develops. Depending on the species, this can be smooth enough to reflect your image, even with pine (almost).
JoeOf course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
4th September 2007, 08:45 AM #7
Not sure I'd go with that bit of advice.
Coating billets/burls all over with wax gets them to the purchaser in one piece, but ensures that you'll have a piece of wood as wet as when it was encased in its wax coat, so go easy on it when you do take the wax off, or you may end up with sevearl bits instead of one! If you have the means, you could check the MC, then at least you would have an idea of where it's at.
For the occasional bit of wood I buy like that, I scrape the wax off the side-grain, and usually plane it to bare wood, but leave the wax on the end grain until I figure out how dry it really is. You want the water to get out, just not too quickly!
Cheers,IW
-
4th September 2007, 09:06 AM #8
Usually those wax cover exotics are green or half green, removing the wax will cause checking and cracking. I'd be careful.
Wood. Such a wonderful substance.
-
4th September 2007, 10:06 AM #9
-
4th September 2007, 10:49 AM #10
I would have thought that the waxed surface would not be the finished surface so just go ahead and turn, cut, plane or scrape as you would if the wax coating wasn't there as it won't do any harm to your tools..... IMHO
Boy, that was a garbled mouthful!
-
4th September 2007, 10:55 AM #11
Chris, this is your best reply in 8 years. Congratulations.
Visit my website at www.myFineWoodWork.com
-
4th September 2007, 11:01 AM #12
Maybe he has been kidnapped & somebody has taken over his keyboard???
Nar.... that wouldn't last.Cliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
4th September 2007, 05:15 PM #13
Well, all I can say is that I was told to do that by the supplier, the first time I bought one. And it worked no problems. I just boiled the jug, put the wood block in the sink and poured the water over it, rotating to make sure all sides covered. The wax came off easily.
I then put it on the drainer and let it dry for an hour or so, before using it.
The wood didn't appear to have absorbed the water and the wax was gone. Some of the pieces of wood I've done this to had natural edges, so it would have been virtually impossible to extract the wax by scraping.
The guy who told me to do this is a very proficient wood turner and that's what he does with his turning blanks.
Qick and easy - and it works."... it is better to succeed in originality than to fail in imitation" (Herman Melville's letters)
-
4th September 2007, 06:15 PM #14
IMHO, it depends on how much wood needs to be removed to reach the "finished surface" and what type of finish you're planning to apply. Wax smears and some finishes don't take kindly to the presence of even tiny bits of wax in the grain. A bit like silicone, really.
If it's being thicknessed, planed, turned or otherwise removed with a blade, then just have at it, unless you're only removing a bee's dick. If it's being sanded to size, then scraping most of the wax off first would be a damned good idea. I've never tried boiling water, so can't comment on that 'un.
A bit of common sense helps.
- Andy Mc
-
4th September 2007, 07:45 PM #15
OK, Jaspr - not looking for an argument. I guess as Skew sez, it really depends on the piece and what you are going to use it for. I assumed the piece was required to be dry for its final use. You would have no idea of the MC on receipt, and might want to let it equilibrate, in which case you would want to get rid of the wax from the side grain but it would surely be prudent to slow down loss from the ends until you were satisfied things are getting near equilibrium. But since turners often prefer to rough out green anyway, Skew's advice to 'have at it' as is, is just as relevant.
Cheers,IW
Similar Threads
-
WOOD KILLS BACTERIA
By ubeaut in forum WOODWORK - GENERALReplies: 41Last Post: 1st July 2009, 07:45 AM -
Not a joke. Just a bit of fun MKIV
By RETIRED in forum WOODIES JOKESReplies: 4138Last Post: 31st January 2007, 01:54 PM -
Wet Wood
By Anthony in forum SAFETYReplies: 8Last Post: 31st July 2006, 10:33 PM -
Working big piece of wood - cracking help!!
By MastaRob in forum WOODWORK - GENERALReplies: 4Last Post: 25th July 2006, 09:42 AM -
exotic wood finish
By dale grible in forum FINISHINGReplies: 2Last Post: 19th October 2004, 10:51 AM