Thread: Colour fill on curved edge

Gday Harry, I just used the follow me tool to fill in one edge on your rack. Cant help more right now....off to race day at the F1..

read through this thread. Filling a curved surface had us all stumped.

Although the "colour in" feature looks good on screen or paper, I cant see any advantage to the actual plans.

If you are happy with the plans as you have drawn them, then go and make it.

PS Harry, your curves are hollow, so they wont colour anyway.

Al

Here is an update version.
I had to make the sides solid by extruding them with the "push/pull" tool, you will see that the back of the sides are still hollow, this is due to you deleting some lines along the way that shouldnt have been deleted.

Al

Just tried using Ivan's method works well.

Still stuck on the component placement tho.

You could try using the TAPE MEASURE to mark a point on the shelf where you want the edge of the component to start.

When you add the component, use the MOVE/COPY tool to move it closer to the spice rack.

Still with thte component highlighted and using the MOVE tool. Click on the corner or edge of the component and try to line it up with the construction point you made with the TAPE MEASURE.

If all else fails. Post the component and someone will bound to place it into your spice rack.

Originally Posted by Harry72

Just tried using Ivan's method works well.

Still stuck on the component placement tho.

Do you mean you're still stuck on using and making components in general?
If so, I know what you mean as it took me a while to figure they were and how to you use them.

Think of it like this. Draw everything as if you were making it in real life. Draw up 1 curved panel that is 18mm thick and make it a component. Then you just make a copy from that (ctrl-click-drag). Draw up a length of dowel, make it a component. Draw a panel for the shelf etc, etc. Once you have all the pieces, you can just join them all together, or join them as you go. If you want to go the whole hack, you can also draw the mortice & tenons etc.

Hope that helps a bit.

Harry, If you're placement ends up miles away, your probably shifting in the wrong dimension: y instead of z, or some such. Try doing a move, and waving the component around a bit slowly, the move line will highlight to one the main axes. If you hold shift down, it will lock the move in this direction. Then just put the placement point aligned with where you want it and release.

Harry, have a play with this one. I have made the white curved end panel as a component.
Try detaching. Try re-attaching and try making a copy of it and delete the hollow one and try attaching the new one.

Also, you have managed to draw the spice rack on a 45°..always keep them at 90° to the axes....

Originally Posted by martrix

Harry, have a play with this one. I have made the white curved end panel as a component.
Try detaching. Try re-attaching and try making a copy of it and delete the hollow one and try attaching the new one.

Theres a problem...

See that diagonal line on the bottom?
It will stop you from doing stuff.
I Have no idea what, but it wont let you do things properly.

Al

Originally Posted by ozwinner

Theres a problem...

See that diagonal line on the bottom?
It will stop you from doing stuff.
I Have no idea what, but it wont let you do things properly.

Al

You mean on the bottom of the new one I just drew?

yeah I just saw that too. That bottom line on the rack isn't at 90° and that probably happened because it was drawn off-axis and its hard to tell if you drawing square lines.

If you want to get this drawing back on the an axis, do this.

Even though it is not a component, if you use the arrow and draw a box that goes around the complete drawing (this will highlight it all), you can move it around as it it was a component.

Once highlighted, select the ROTATE tool. Put the protractor on the corner of the drawing. Make sure the protractor colour is blue.
- Click once when on the corner. Move the line so it is parallel to the drawing and click the mouse again. Now you should be able to roatate it around.
- Rotate the object 43 degrees to get it back onto one of the axis's.

Abug, legend. You just taught me something.

Here it is now back on axis......over to you Haz

Anytime.

I'm one of those "LURKERS". I read to get tips on all different things but never really post as in forums there is usually someone who likes nitpicking things people say.

But if I can offer help or advice, i'll post.

And yes I Love Sketchup.

On axis... so the blue line should always point upwards?

Is this on axis properly?