Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 20 of 20
Thread: Grinding wheel dressers
-
28th October 2007, 09:27 AM #16
Wheel dressing
Hi guys
If I can offer a me too?
Its a co incidence that I should see this post .On Friday I finished dressing all the wheels in the classroom workshops at school cos the safety inspector from WH&S was coming.
I had been previously been around and dressed them with the single diamond point that fitter had lent me. I found that the diamond tool bounces a lot on the wheels and they were not terribly concentric.
Having one of those Norton dressing sticks made of the similar material as the wheel but a tad coarser,I took it to school and went over the wheels as done by the diamond.
The stick leaves a much finer surface finish and the they are concentric and don't vibrate to the extent which they did before.
The bloody inspector turned up and said bugger all about my beautifully dressed wheels but plenty about the useless plastic guards ( the kids press them into the rotating wheels) and crash stops which are required at knee height on every machine.
I am impressed at the excellent surface of the wheel left by the stone.I have no trouble sharpening our biggest taper shank drills (25mm) on the large (350 diameter wheel) normally employed in grinding mild steel.
GrahameLast edited by Grahame Collins; 28th October 2007 at 09:28 AM. Reason: I ken spel but my fingurs kan't
-
28th October 2007 09:27 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
28th October 2007, 10:28 AM #17
Diamond cutting wheels for the 4" angle grinder are great wheel dressers... Buy 'em from the $2 shop. They make great, cheap dressers. They usually cost about $12 for a pack of two.
-
28th October 2007, 10:50 AM #18Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
I find the carborundum sticks do a good job of cleaning the Al. Ox. wheels but leave them too smooth. To roughen them (for betting grinding) I use the diamond point dresser, and use it roughly. Even then, when you feel the wheel surface its clearly smoother than the untouched wheel side. Seems a star wheel is necessary.
Cheers, Ern
-
28th October 2007, 11:28 AM #19
Great tip, Chris. Wish I'd heard of it a couple of years ago before I bought the single point & the T bar dresser...
I think I read somewhere that the single point dresser leaves the wheel "sharper" than the T bar type, but to achieve this the s.p. dresser must be moved across the wheel at a steady, not too slow, rate so it's not rubbing on the just sharpened abrasive. Hence the idea, taken to a conclusion, of the flash tormek dresser that has a "lead screw" type design.
I've found the t bar easiest to use, but intend making a copy of the Oneway jig like Stu from Tokyo made, that allows very small adjustment. Still need to hand feed across the wheel surface, though.
The beatings will continue until morale improves.
-
28th October 2007, 01:18 PM #20
Not quite the same but along the same lines.
I used to do contract work brazing the diamond tips on concrete cutting blades and I asked the boss man if I could have a bit for dressing, so he gave me a bit of diamond impregnated carbide about 10mm x 10mm x 25mm to which I silver soldered a bit of rod onto it for a handle and this is the bees knees, it rips into grinding wheels beautifully.Cheers
DJ
ADMIN
Similar Threads
-
After fine grade grinding wheel
By Mark Woodward in forum WOODWORK - GENERALReplies: 1Last Post: 22nd June 2007, 06:06 PM -
If you know much about Abbott & Ashby 8-inch bench grinders please read on.....
By Mirboo in forum HAND TOOLS - POWEREDReplies: 12Last Post: 14th February 2007, 10:23 PM -
Grinding wheel "bounce"
By philly in forum WOODTURNING - GENERALReplies: 20Last Post: 25th January 2006, 11:54 AM -
wetstone grinding wheel replacement
By reeves in forum WOODTURNING - GENERALReplies: 9Last Post: 15th December 2005, 03:20 AM -
Grinding Wheel
By Babytoolman in forum WOODTURNING - GENERALReplies: 7Last Post: 18th January 2005, 06:29 PM