Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: where do I buy a base for metabo
-
30th October 2012, 08:27 AM #1
where do I buy a base for metabo
Chaps, anyone know where I can buy a new 7 hole base for a Metabo sander in Melbourne?
I am also looking for "F" brads for a brad gun, all the shops I have ried only stock "C" that don't fit my gun....
Pappy
-
30th October 2012 08:27 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
30th October 2012, 08:33 AM #2
where do I buy a base for metabo
I purchase a new base a few years ago at the wood show directly from Metabo but I think the stand was run by Total Tools. I am sure that if they do not carry it as stock it could be ordered in for you.
Now proudly sponsored by Binford Tools. Be sure to check out the Binford 6100 - available now at any good tool retailer.
-
30th October 2012, 09:06 AM #3
Any TOOL SHOP that sells METABO TOOLS , will be able to supply a new base , what is the issue wih the old one//.
If the Velcro Pad is worn , these can be replaced with out replacing the whole Base Unit.
As for the Brads, sorry cannot help you there.
Jeff
vk4
-
30th October 2012, 11:20 AM #4
.
Thanks boys, yes the velcro is worn and needs replacing.
Jeff, how do I replace the velcro and where can I get it?
I tried Total tools no good they have to order it for me. The issue is I live in Yarrwonga and will be in Melbourne on Wednesday only
-
30th October 2012, 11:31 AM #5
My velcro was beyond saving so I invested in the new base. There were a few options of different firmness levels of the foam material. The big difference that I noticed when replacing was just how worn / damaged the perimeter of the old base was which I didn't really notice until I put the new one on. It was more user abuse than anything else as I often use the sander for bandsaw boxes and the like which tends to ding up the perimeter of the foam more than just using it on a flat surface. With the new base the paper was supported to the very (sharp) edge and stayed on much better (in addition to the new velcro) ..... unfortunately now the "new" one is also getting a bit worn!
If timing doesn't suit for pickup how about mail order. The base itself is quite light and could be easily mailed in an Australia Post satchel for under $10.Now proudly sponsored by Binford Tools. Be sure to check out the Binford 6100 - available now at any good tool retailer.
-
30th October 2012, 12:13 PM #6
Velcro is available from ABRASIFLEX , BUNNINGS, again any store that sell tools should have it, Sandpaperman , on this forum should also sell it.
To remove the old Velcro I normally sand / grind back with a small angle grinder and a 60Grit disc then smooth off by running the base flat on a sheet of 80grit paper.
this is as long as the foam on the base is not too chewed about.
Jeff
vk4
Similar Threads
-
Metabo
By Bob38S in forum HAVE YOUR SAYReplies: 1Last Post: 6th August 2010, 08:15 PM -
Metabo ROS or other?
By Waldo in forum HAND TOOLS - POWEREDReplies: 13Last Post: 3rd April 2008, 09:49 PM -
Metabo Code
By Sprog in forum HAND TOOLS - POWEREDReplies: 0Last Post: 15th December 2004, 04:23 PM