Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 26 of 26
Thread: cutting steel with a chain saw?
-
30th April 2007, 12:29 PM #16
Matrix,
Suggest you see this silly post I did a while back that shows the outfit on a redgum burl out west. https://www.woodworkforums.com/f40/happiness-redgum-burl-handtools-32276
The mill is a Westfords 48", the bar is a titanium 56" and the motor is a Stihl 95cc. As noted earlier I went for the heavier chain too - seems to make sence on such a large outfit.
The chain we used in this mango will now become my second backup chain even though it was new before this milling but so many nails and resharpens it will be replaced and just kept aside.
So now i will have two back up chains - the other one has some rounding of the chain where it can be effected by the drive on the motor - I keep that one only for emergencies - not dangerous but will get me out of a jam if in a remote location and nearly finished and have another chain go out of use.Cheers
TEEJAY
There is a very fine line between "hobby" and "mental illness"
(Man was born to hunt and kill)
-
30th April 2007 12:29 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
30th April 2007, 12:59 PM #17
And your point is? says the missus... who wants to buy a new house anyway so whats a rotary cloths line in the scheme of things
Why not drop a standing tree?... I mean Ive got a few here I DEFINANTLY intend to drop before we put the place on the market and have milled before we leave... I refuse to leave behind the bloody great Camphor Laurel nor the Elm out the front or the holeyshytethatstall some thing or other tree down near the creek or even the three pauliwanna trees out the side of the driveway maybe not the straightest trees on the block but the wood is good for makin stuff... they are coming!!
But why not drop a standing tree?Believe me there IS life beyond marriage!!! Relax breathe and smile learn to laugh again from the heart so it reaches the eyes!!
-
30th April 2007, 02:49 PM #18
Dropping a standing tree can be made safer with planning and a pulling line.
To estimate the landing point of the top, tape a hand level to the bottom of a whatitsname (45-deg triangle for crosscutting with a circular saw) and sight the top along the hypotenuse; extend the sight line to the ground.
Use a stout rope, or better yet a chain, for a pulling line. Attach as high as you can get on the trunk. I once dropped a 50-ft pine northward when it was leaning about 15 deg south (hanging over neighbour's power line). Used a chain and two come-alongs by leap-frogging along the chain. Left a generous hinge for softer bending of the trunk, and pulled a bit, cut a bit, pulled a bit, cut a bit, etc. And stand off to the side after the last pull. Was a few feet off target and landed on a shrub, but didn't hurt it much.
Extra chains, yes. Extra chain saw(s) even better.
JoeOf course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
30th April 2007, 05:58 PM #19
-
3rd May 2007, 08:19 PM #20
No some photos from the adventure.
the stump in standing situation.
the stump was about 1800mm (6 foot) tall and about 1200mm (4 foot wide)... the depth is a matter for dispute
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
3rd May 2007, 09:04 PM #21
what the stump was holding up acouple of weeks before.
Neil made contat with the owner of an EX mango tree & called me in because he need help to chew on it.
Of course there is always more there than you think.
add to these two loads the girly load that neil took
In fairness neil wisely didnt want to push his trailer too hard (it isn't happy)
you can see some obvious big bits......There are bigger ones on the bottom
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
3rd May 2007, 09:15 PM #22
now back to the slabs
we got 6 decent slabs all up and the scrag end after the first cut.
I took these two and the scrag end.
I've already cut up the scrage end into 30mm square stock & packed it away to dry.
Do not adjust your monitor.... and no I havn't fiddled with the colour.
the reason the slabs are bright yellow, Is that I sprayed them with borax to deter borer and to inhibit the dreaded blue mould.
I hope it will all come off when I thickness.
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
5th May 2007, 08:56 PM #23Neil____________________________________________Every day presents an opportunity to learn something new
-
7th May 2007, 12:55 AM #24New Member
- Join Date
- Jul 2006
- Location
- Tasmania
- Age
- 44
- Posts
- 6
I reckon your chain could easily cut through that stuff.
I was removing an old stump a few months back and managed to cut through an old plane blade that it had grown around. Needless to say the chain was stuffed but it did manage to get through it.
-
12th May 2007, 03:01 PM #25
further pics of the final slice & dice of what was left over.
Soundman.... thtas me
slicing & diceing.Any thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
12th May 2007, 03:08 PM #26
and the end result.
note the warn out engineer recovering in the shade.
Note to those prospecting for back yard mango.
green mango is quite heavy
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
Similar Threads
-
Cutting stainless steel pipe
By ratchet in forum METALWORK FORUMReplies: 13Last Post: 21st September 2009, 09:51 PM -
Should I wear a dust mask while cutting steel with an angle-grinder?
By Rocker in forum SAFETYReplies: 15Last Post: 11th February 2007, 05:07 PM -
Welding question ? ... Is this dangerous ?
By JDarvall in forum WELDINGReplies: 36Last Post: 9th March 2006, 12:29 PM -
Finally, a chain letter i like
By doug the slug in forum WOODIES JOKESReplies: 1Last Post: 20th July 2005, 11:42 PM