Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 12 of 12
Thread: I'm gonna turn it on.....
-
18th August 2006, 07:58 PM #1
I'm gonna turn it on.....
OK I bought the Ryobi thicknesser and I've stacked up all the timber I want to dress next to it and I'm gonna turn it on tomorrow.
Thing is there are a few bits left over and I'm not sure what to do with them.
Pic 1 - The thicknesser
Pic 2 - Some of the timber
Pic 3 - A safety guard :eek:
Pic 4 - The dust chute
Now based on the limited instructions it looks like it's either the dust chute or the safety guard so as the chute was already fitted I'll put the safety guard to one side, yes?
HH.Always look on the bright side...
-
18th August 2006 07:58 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
18th August 2006, 08:02 PM #2
..but there's more....
pic 5 - Blade setting gauge but no instructions on how to use it :confused: ??
pic 6 - Some other bits, I think these are for the safety guard and to bolt it down to something? :confused:
pic 7 - Dust chute enlarger, I know what this is for
So the question is can I just turn it on and start using it or do I have to use / install any of these bits?
HH.Always look on the bright side...
-
18th August 2006, 08:08 PM #3Originally Posted by HappyHammer
Go to the GMC site and DL the manual for the thicknesser. Same machine, same blade setter. Not the most detailed instructions but you'll get the gist of it.
http://www.gmcompany.com/download/pr...000_Manual.pdf
Cheers,<>
Hi, my name is Glenn and I'm a tool-o-holic, it's been 32 minutes since I last bought a tool......
-
18th August 2006, 08:20 PM #4
Thanks Glenn better than the one I got with.
HH.Always look on the bright side...
-
18th August 2006, 08:53 PM #5
If you go to the Ryobi Australia website, there is a downloadable set of instructions that are a lot better than the GMC version!
Have a nice day - Cheers
-
19th August 2006, 06:48 PM #6Originally Posted by Wood Butcher
HH.Always look on the bright side...
-
21st August 2006, 10:11 AM #7
Turned it on and it worked great and I didn't injure myself, even better.
I recycled some pailings from a fence we've just taken down to make way for our extension (my new garage ) and I was told it was Yellow Gum. Hadn't heard of this so I ran it through the Ryobi and sure enough it had yellow shavings. I'm gonna recycle the pailings and make a privacy screen for the back garden, I'll post some pictures when I get to it.
I then ran the rails through the thicknesser and discovered they were redgum, so I scored about 10m of 50mm x 50mm redgum for nothing
I'll take some pictures and post them tonight if I get a chance. Best of all it has given me the justification with SWMBO to buy a dust extractor
HH.Always look on the bright side...
-
21st August 2006, 05:58 PM #8
They are also great for finding nails
If you happen to ding the blade just offset the two slightly so the 'ding' is negated with each blades offset.
This will appear as a slight raised line running along the timber, a bit of grit in fcat, just about anything will do it.Stupidity kills. Absolute stupidity kills absolutely.
-
22nd August 2006, 01:20 AM #9
"just about anything will do it."
Originally Posted by Iain
tell me about it !!!!
i have two raised lines already GRRRRR
good luck with the Ryobi
cheers
tonySA
-
22nd August 2006, 12:36 PM #10Senior Member
- Join Date
- Dec 2004
- Location
- Brisbane
- Posts
- 464
Hi,
I've got the carbatec equivalent (same) I did read the instructions about the blade setting jig. Whilst the instructions were better than GMC I was still not convinced they weren't good.
But there's more. Due to too many metal thingies and blade nickies I am about to learn using the jig. I am hoping it will be fine and I don't have to buy those magnetic jigs for $89 which I am told are very good.
Wil let you know how I go.
cheers conwood
-
22nd August 2006, 08:33 PM #11
Having replaced the blades on mine once and reversed them twice I can tell you that the setting jig is quite easy to work out once you get down to actually doing it.
As for "dingging" the blades the best investment you can make is a metal detector.
Himzo.There's no such thing as too many Routers
-
22nd August 2006, 10:39 PM #12Originally Posted by himzolStupidity kills. Absolute stupidity kills absolutely.
Similar Threads
-
So when do you first turn on the heating?
By craigb in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 42Last Post: 1st May 2006, 06:16 PM -
First Turn
By CameronPotter in forum WOODTURNING - GENERALReplies: 10Last Post: 8th January 2006, 09:58 AM -
Turn Around 2000
By RETIRED in forum ANNOUNCEMENTSReplies: 0Last Post: 14th September 2000, 04:31 PM