Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 19
Thread: Mistery object -a new one
-
3rd September 2007, 12:45 PM #1
Mistery object -a new one
Hi folks, I thought it was about time for another one.
Came across this in one of my tool boxes yesterday. Every time I had noticed it before I had simply thought that it was a tool for joining carpet as I have a couple of those that look kinda similar.
But for some reason I thought I'd give it a closer look and I got suspicious.
Its marked "Original Sievert" "Type 3610" Max Sievert Sweden" It has a wooden handle painted Army Karki Green.
Did a quick Google so I think it must be something to do with hot metalworkWho knows........it could be as common as muck for all I know!
Attachment 54736
Attachment 54737
-
3rd September 2007 12:45 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
3rd September 2007, 12:50 PM #2
Very small as well
I may not have gone where I intended to go, but I think I have ended up where I needed to be.
My Other Toys
-
3rd September 2007, 12:53 PM #3
-
3rd September 2007, 12:58 PM #4
You heat it up till it's red hot, then roll it across your forehead for a nice, decorative pattern - particularly attractive to Klingons, apparently.
GWWhere you see a tree, I see 3 cubic metres of timber, milled and dressed.
-
3rd September 2007, 12:58 PM #5I may not have gone where I intended to go, but I think I have ended up where I needed to be.
My Other Toys
-
3rd September 2007, 01:00 PM #6
It's a grinder wheel dresser.
"I don't practice what I preach because I'm not the kind of person I'm preaching to."
-
3rd September 2007, 01:04 PM #7
I agree with SilentC - I have a picture of one like that in a 1970's text (NSW) on metalwork
Cheers
Jeremy
If it were done when 'tis done, then 'twere well it were done quickly
-
3rd September 2007, 01:04 PM #8
Wot Silent sed
Alastair
-
3rd September 2007, 01:09 PM #9
OK How do you use it. It sounds like it could be useful?
-
3rd September 2007, 01:13 PM #10
Well, if it is a wheel dresser, you start the grinder, then turn it off when it gets to full speed, then hold the dresser against the rotating wheel and move it side to side. It cleans the swarf out of the wheel and removes grooves.
"I don't practice what I preach because I'm not the kind of person I'm preaching to."
-
3rd September 2007, 01:15 PM #11
Re Grinding Wheel Dresser
Bleeding.....Grab it by the handle and place the rollers against the face of the grinding wheel. Apply sufficient pressure to face the grinding wheel.The wheel will cause the rollers to rotate and this will dress the face of the wheel. Make sure you wear the usual safety glasses and be prepared from some dust.....
rgds
RuddyAnd my head I'd be a scratchin'
While my thoughts were busy hatchin'
If I only had a brain.
-
3rd September 2007, 01:15 PM #12
-
3rd September 2007, 01:15 PM #13
Thanks Guys, Silent you win the Lolly Pop - I'll send it be email.
Just found this. Also this was obviously way too easy ..might go searching in the shed....
http://www.sievert.se/us/gwd.htm
-
3rd September 2007, 01:19 PM #14
With the grinder running, hook the 2 "legs" over the toolrest, and then raise the handle until the 'wheels' make light contact with the spinning grinding wheel. As they whizz around, they repeatedly bash into the grinding surface, knocking out bits of blunt grit, and exposing new sharp grit.
Note however that it will not true up an out of round wheel very well. To do that you really need a diamond dresser, (either bar type or single point, depending on your preference). These tend to leave a slightly blunted whel, so ideally you first true up with the diamond, and then freshen the grit with the wheel dresser.
Once that is done, all you will need to do for some time, is to touch lightly with the wheel dresser, to freshen up the grinding surface.
Hope this helpsAlastair
-
3rd September 2007, 01:19 PM #15
Like the Silent C says but notice, there is a "Hook" on the edge of the handle (a small protrusion) hook that over the edge of your tool rest on the grinder and run the tool back and forth across to true up the emory of the wheel. Cleans off all imbedded matter in the wheel and flattens the face according to the leading edge of the tool rest.
The one you have is considerable old but they still make them today.. in fact I bought a replacement just last year.
Similar Threads
-
Mystery Object - what is it??
By old_picker in forum HAND TOOLS - UNPOWEREDReplies: 10Last Post: 18th February 2007, 08:39 AM -
Electrolysis - removing rust from ferrous tools
By Shedhand in forum HINTS & TIPSReplies: 26Last Post: 7th February 2007, 03:58 PM -
If money was no object what sorta Car would you have?
By echnidna in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 52Last Post: 17th June 2006, 11:39 PM -
Mystery Object
By ozwinner in forum Woodies Quiz ForumReplies: 268Last Post: 2nd July 2004, 04:19 PM