Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: ML-392 Options
-
15th June 2005, 12:52 AM #1New Member
- Join Date
- Jun 2005
- Location
- Perth WA
- Age
- 58
- Posts
- 4
ML-392 Options
Stats: I'm in Perth; have a small workshop; need a combination planer/thicknesser.
After spending some time working the the forums I think I'm prepared to risk an ML-392 type machine. The cost is about right for what I can afford vs what I need it to do (NB Have assumed I will need to include refit of the drive gear arrangement with new bearings, shaft straightness checks, align and re-secure chain gears, etc...)
However, I am locally bereft of choice. Carbatec-WA no longer stock this item (due to quality hassles). Timbecon is only remaining local provider I know, but I've heard mixed reviews of their machine quality. Any feedback gratefully received.
Other options for this model machine are on-line or by phone from:
- Tama @ $1,155 + shipping from Sydney http://www.tama.com.au/LEDA%20combinations.htm
- Ledacraft @ $1,155 + shipping from ??? http://www.ledamachinery.com.au/cgi-...products_id=36
The only alternatives are to go big time $ into a Euro version like the Metabo (at 2.5x the price). Would an ML-393 be better? Does it have the same quality problems as the 392?GS
-
15th June 2005 12:52 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
15th June 2005, 01:07 AM #2
Grainstruck,
I have an ML-392 from Timbecon. I have had it for about a year now and find it very good the only complaint I have are the short tops however planing lengths 2mts or less isn't a problem. My experience with Timbecon has been very good. The only problem I ever had with something I bought from them wasn't a problem getting fixed and I have a whole workshop with mostly their equipment. I would recommend them as a supplier.
Kind regards Vasco
-
15th June 2005, 11:16 PM #3New Member
- Join Date
- Jun 2005
- Location
- Perth WA
- Age
- 58
- Posts
- 4
Vasco,
Many thanks. Your experience helps ease my mind.
cheersGS
-
16th June 2005, 12:11 AM #4
If you've searched the forums as you said, then you'll see that i'm pretty happy wth the ML392 . For the price it's a good machine (under $1000). The only real complaint is the crappy fence setup but i thiunk that's typical of the low end machines. I have to adjust mine every time i set it up usuin a sqaure on the table. Otherwise, the finish is good and no probs with power. I ran some spotted gum through it and that's about as hard a timber as you can get - only thin boards but no probs.
If at first you don't succeed, give something else a go. Life is far too short to waste time trying.
-
16th June 2005, 12:51 AM #5New Member
- Join Date
- Jun 2005
- Location
- Perth WA
- Age
- 58
- Posts
- 4
Gumby,
Thanks also.
Do you know of anyone who has a machine by Leda or Tama?
I checked out the Axminster site and found a/the manual for the AW106PT at this address http://www.axminster.co.uk/viewindex...cle_id=manuals - under "Woodworking Machinery"
NB Assume the PT suffix is not a step change in design - the manual states it is the ML-392 model.
I'll try condense the big thread into the possible maintenance checks.
The manual also idenfies Axminister's source factory as Laizhou Planet Machinery Company (also under site http://www.planetmach.com/index.htm). Is this the same source for Timbecon or the others? The "about" page is interesting - the place looks pretty flash (big metrology room, assembly line, etc)
regdsGS
-
16th June 2005, 11:34 AM #6Originally Posted by grainstruck
Originally Posted by grainstruck
Yes, that's the manual most of the ML392 owners in here have downloaded. It's not brilliant but much better than what you get with the machine
Originally Posted by grainstruck
Not really sure about that. I haven't looked into it that much. I'd say timbecon is the place to go shopping for one. I've never purchased from them but all the reports from those who have seem very good.If at first you don't succeed, give something else a go. Life is far too short to waste time trying.
Similar Threads
-
Cheap SCMS - What are the other options
By theRat in forum HAND TOOLS - POWEREDReplies: 24Last Post: 10th June 2005, 09:15 AM -
Best Options for Crosscut Saw
By Ranger in forum HAND TOOLS - POWEREDReplies: 9Last Post: 3rd August 2004, 11:07 PM