Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Why have reverse?
-
5th December 2004, 10:58 PM #1
Why have reverse?
Does anyone know why some spindle moulders have reverse? I've worked with them before and noticed that they (and the power feed) could run in either direction. I'd never paused to consider why anyone would need this as you'd need to invert the cutter block to get it to work. My newly acquired spindle moulder has no switch or plug and now would be the time to fit a reversing switch if there's any benefit.
Mick"If you need a machine today and don't buy it,
tomorrow you will have paid for it and not have it."
- Henry Ford 1938
-
5th December 2004 10:58 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
6th December 2004, 08:20 AM #2
Mick,
I have briefly used a spindle moulder where reverse was used. It was used on a chair leg for shaping the chair leg. Because of the curve of the leg, the grain changed place a couple of times or to put it another way, the curve crossed the grain a couple of times.
If you used the spindle moulder in one direction for the length of the leg, half of the leg would have tearout. You mould the leg in two runs, first one in forward for the sections where you are cutting with the grain and then you flip the cutter and reverse the motor and complete the other parts.
In other words, all the leg is cut with the grain.
The chap who was showing me this makes large batches so it is not as inconvenient as it sounds.- Wood Borer
-
6th December 2004, 10:11 AM #3
Rob's dead right Mick.
However you can do the same work in a single direction if you climb cut. To climbcut safely means you must use a power feed. Which is a great accessory to a spindle moulder anyway. You can climb cut everything and it doesnt matter which end of a stick you put in first to get no-tearout moulding.
-
6th December 2004, 10:31 AM #4
I bought the spindle moulder for making doors and windows (so no curves) and I already have a power feeder so I don't think I'll bother about the reversing switch.
Mick"If you need a machine today and don't buy it,
tomorrow you will have paid for it and not have it."
- Henry Ford 1938
-
6th December 2004, 06:01 PM #5Registered
- Join Date
- Aug 2003
- Location
- .
- Posts
- 10,482
Reverse is for puting back on material, that you took off by mistake.
Al
-
6th December 2004, 06:16 PM #6Originally Posted by ozwinnerSome People are like slinky's,
They serve no purpose at all,
but they put a smile on your face when you throw them down the stairs.
-
6th December 2004, 07:50 PM #7Why have reverse?Photo Gallery
-
6th December 2004, 09:30 PM #8
You can also get some of the older imported cutters are "handed". Some are made to clockwise and some anti-clockwise. We have some of both in the workshop.
Originally Posted by echnidnaHave a nice day - Cheers
-
6th December 2004, 09:48 PM #9
Is climb cut the some as backcut or back fed? Would really like to know as the lingo from shop to shop does change but sometimes means the same thing.[/QUOTE]
Back feeding against the cutter direction as you have said WoodButcher.
Extremely dangerous even with a router.
But with a router one has to brace oneself against the 'throw' of the router.
Whereas with a power feeder throw is controlled.
CheersJohnno
Everyone has a photographic memory, some just don't have film.
-
6th December 2004, 10:52 PM #10Originally Posted by ozwinner
Mick"If you need a machine today and don't buy it,
tomorrow you will have paid for it and not have it."
- Henry Ford 1938