Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: broken chainsaw need help
-
1st June 2009, 06:35 PM #1SENIOR MEMBER
- Join Date
- Dec 2007
- Location
- yarra valley
- Posts
- 683
broken chainsaw need help
i thought i'd put this here as most of you blokes are on top of this kind of stuff. a mate dropped this saw in the other day, he's busted the studs off the saw that holds the bar on. i've had a go trying to get them out with the multi grips but they don't budge and i don't want to put too much pressure on them in case i snap them any further. the make is a Talon brand. my questions are if anyone has played with theese thing before ;do i put more pressure on the stud or do i have to pull the thing apart ? or is it just better to throw the thing in the bin?
-
1st June 2009 06:35 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
1st June 2009, 06:48 PM #2SENIOR MEMBER
- Join Date
- Feb 2004
- Location
- kuranda north qld
- Posts
- 717
put a little heat on the studs may help ! carefully and get the mix out first ! or get a better saw.
-
1st June 2009, 08:01 PM #3Senior Member
- Join Date
- Mar 2009
- Location
- Coffs Harbour
- Posts
- 185
If they're studs they will come out with proper persuasion. Can you use an extractor set, where you drill a hole straight into the centre of the broken bolt, and insert the extractor? Only use good quality or these will snap off too
-
1st June 2009, 08:26 PM #4
What Bob said, a bit of heat, doesn't need to be red hot.
A hot air gun or hair dryer directed straight on to casing where the studs are.Cheers
DJ
ADMIN
-
2nd June 2009, 12:21 AM #5.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
What DG Said. Heat an go for it. If you break a stud off you should be able to use stud removers. If you end up mangling the case just bin it.
-
2nd June 2009, 10:22 AM #6
Charlsie I thought the bar retaining studs were square headed bolts with a knurled shank that were pressed in from the starter side , I was under the impression that these saws were designed on the last of the McCulloch range you may just have to strip the saw down by removing the cowl that holds the oil-fuel tank on , and tapping the bolts through .
Does the saw look like this on if so then the studs come out the way I said Peter
Attachment 106867Chainsaw Enthusiast
-
2nd June 2009, 01:01 PM #7.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
-
2nd June 2009, 01:53 PM #8
-
2nd June 2009, 02:05 PM #9
This is a quote from McBob's McCulloch chainsaw site
Near bankruptcy, its 1999 acquisition by the Taiwanese company Jenn Feng Industrial Co., Ltd .
The McCulloch name was partially purchased by Husqvarna AB for use in Europe only,
where Jenn-Feng equipment is labeled as the Talon brand rather than McCulloch.
Peter
Chainsaw Enthusiast
-
3rd June 2009, 08:13 AM #10SENIOR MEMBER
- Join Date
- Dec 2007
- Location
- yarra valley
- Posts
- 683
peter, youv'e nailed it right on the head .thank you, can't tell you how much i appreciate your time and effort regards charlsie
Similar Threads
-
Broken down car
By Allan at Wallan in forum WOODIES JOKESReplies: 3Last Post: 7th October 2007, 08:50 PM -
Broken wet wheel
By Groggy in forum SHARPENINGReplies: 26Last Post: 28th August 2007, 01:45 PM -
broken plane, broken heart
By fletty in forum HAND TOOLS - UNPOWEREDReplies: 17Last Post: 15th July 2007, 01:55 PM -
Broken belt
By Stevenp in forum HAND TOOLS - POWEREDReplies: 10Last Post: 10th July 2007, 11:19 PM -
chainsaw mill & a good big chainsaw
By Cliff Rogers in forum HAND TOOLS - POWEREDReplies: 33Last Post: 18th April 2006, 08:51 AM