Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Cedar Tips Please
-
17th January 2010, 01:08 PM #1Novice
- Join Date
- Nov 2009
- Location
- Doonan Qld
- Posts
- 14
Cedar Tips Please
Hi
Cut up a cedar a few months ago with an alaskan mill using an ms880. So easy to mill. Felt like superman cutting through butter with a hot knife. Now here's the odd thing. Now I'm trying to resize the slabs with a table saw and you wouldn't believe how difficult it is to cut. with a normal tct ripping blade. Scorched timber and a real effort. Can some give me some tips on where I can get a 12in blade that'll give a clean cut? The nature of the timber is quite fibrous, Toona australis
Would appreciate some help
Ta
Pete
-
17th January 2010 01:08 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
17th January 2010, 01:31 PM #2
...bandsaw might be the go..
Or, sounds like the timber is binding on your fence as it's going through the blade.
I have the tail of my fence about 0.5mm further away from the blade when doing big ripping.
...cheers
check your pm Pete
Glenn
-
17th January 2010, 02:34 PM #3Novice
- Join Date
- Nov 2009
- Location
- Doonan Qld
- Posts
- 14
mm binding
Thanks Glenn
Could be
Tried it in a friends large saw too and had the problem and this was a 10hp 3ph saw. Changed the sawblade to an old non tct open tooth blade and seemed to be better but I don;t know where I could get an old 12in blabe to fit my saw. Any idea if they're still made?
-
17th January 2010, 04:40 PM #4
Yes they are still made and you should be able tto get one through any good saw service or decent tool shop. Tct should cut as well or better though and for much longer. Cedar should cut quite easilyit may be possible that you need a blade with less teeth and a more open gullet if the slabs are very thick but I imagine that the slabs would not be more than about 75mm thick so chip clearance shouldn't be a problem. you really need to give a bit better description and some photos so that people can be of more assistance.
have you tried cutting it with a handheld circular saw and if so what were the results? if this cuts it alright then you should not have a problem cutting it with a table saw, and if it does cut it alright then it means that something in the setup of your saw is wrong and it is compressing against the body of the blade which will be visible on the blade as rub marks. Either that or you are getting a build up of sawdust in the cut.
-
17th January 2010, 07:27 PM #5
The timber isn't closing on itself have the cut is it? Does your tablesaw have a riving knife or splitter on it?
Cheers
DJ
ADMIN
-
18th January 2010, 01:02 AM #6
blade in the right way... sorry i usually only put the blade in backwards when i cut something to short and need to make it longer again. sorry again
try winding the blade up to full height and if you can pull the ripping fence back to near the centre of the bladeits only short one end!!
-
18th January 2010, 05:53 AM #7
Check to see your slab hasn't twisted. This will cause the blade to bind as you run the slab over your saw table.
Don't ask me how I know this.Last edited by KevM; 18th January 2010 at 05:54 AM. Reason: spelling
Kev
-
18th January 2010, 07:00 AM #8Novice
- Join Date
- Nov 2009
- Location
- Doonan Qld
- Posts
- 14
yes these are all good points
but have checked all of the above.
I'm cutting 4inch slabs into 1inch boards.The furry fibrous nature of the timber tend to gum the tct blades up. I've tried some smaller sizes with an old smaller non tct blade and seem to get a better cut. I will try to find an old 12in open tooth blade from other sources. Thanks for all the good advice
-
18th January 2010, 05:15 PM #9SENIOR MEMBER
- Join Date
- Feb 2004
- Location
- kuranda north qld
- Posts
- 717
you should use a ripping blade [less teeth and more clearance ] the 80plus teeth of crosscut s are not designed or good for wet??? timber , cedar can be fluffy or fibrous . but a good ripping blade& riving knife should handle it fine . make sure the blade is well above the top off the wood though. your local saw doctor should be able to set you right . feel free to drop some off to me and i will show you ho its done cheers Bob
-
18th January 2010, 06:36 PM #10Novice
- Join Date
- Nov 2009
- Location
- Doonan Qld
- Posts
- 14
new blade
Cheers Bob
Have got a better quality blade now, The blade I was usinfg only had 40 teeth but was of questionable quality. Pretty flexi too. New blade is 32t and seems to be cutting quite clean and fast.
The old lesson is, you get what you pay for.
Peter
-
18th January 2010, 06:41 PM #11
Similar Threads
-
tax tips
By mako in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 27Last Post: 18th February 2008, 06:53 PM -
TIPS for DIY
By jow104 in forum Links to: WEB SITESReplies: 0Last Post: 5th November 2004, 07:24 PM -
More Tips
By mat in forum HINTS & TIPSReplies: 0Last Post: 17th June 2004, 10:27 AM -
top tips
By Gino in forum WOODIES JOKESReplies: 0Last Post: 19th October 2002, 12:43 AM -
Tips, Tips, and more Tips
By Mark Woodward in forum HINTS & TIPSReplies: 0Last Post: 20th January 2000, 10:18 PM