Needs Pictures: 0
Results 1 to 12 of 12
-
4th January 2016, 10:52 PM #1SENIOR MEMBER
- Join Date
- Oct 2011
- Location
- Langwarrin
- Age
- 43
- Posts
- 952
First crack at a CS Mill - Cypress Pine
Hey all,
Finally had a chance to give my chainsaw mill a proper try out after purchasing it at the WWS in 2014.
Its a Granberg small log mill on my Stihl MS251. I had a chain ground for ripping at an angle of 15o (I think, was a while ago)......I know BobL will have a go at me about an underpowered chainsaw for such operations (only 45cc), but when I purchased the saw I wasn't sure how deep into the woodworking I was going to get, and when I purchased the mill I wasn't sure how deep into the milling I was going to get.
If this first experience is anything to go by, a new saw and larger mill will be on the cards sooner rather than later. At least I will still have a smaller, manageable saw to get the cross cutting and small jobs done!!
Onto the show. My Auntie dropped quite a few trees at her place over the year. A great looking Southern Silky Oak (currently being looked after by another valued member of the forum) a messmate (same boat as the oak) and a massive cypress pine. The cypress main trunk was about 4m tall with a multitude of offshoots above that. The offshoots were what I was cutting up as are all between 300mm and 500mm DIA. The main trunk was apparently a nightmare to cut down, so that has been turned to firewood (and some very rustic steps, seats etc).
There are about 12 logs in all, all straight and cut to about 2.4m length. Given they were pine, I thought it would be a great way to get introduced into the art of milling. Both due to the general softer nature of the timber, and also the fact that it isn't worth MASSIVE money, so if I/when I stuff up, it isn't wasting a beautiful slab.
IMGP7018.JPG
Lucky it was pine, as I hadn't really thought the whole process through. lifting the logs onto my stools wasn't impossible, but with myself and Adam (trusty BIL) we managed without too much grunting. If they had of been any sort of hardwood, I'm guessing the milling would have happened at ground level.
I don't love the initial setup for the first cut, but I'm planning on getting rid of the alloy end brackets, and just screwing something to the log, and then the cross rails down to them. would save some hassle, and feel a little more solid. We ran a couple of batten screws up from the saw stools into the log to hold it in place. Just means I had to make sure my final cuts were either above this screw line, or I took the screws out at the last minute.
IMGP7022.JPGIMGP7023.JPGIMGP7027.JPGIMGP7032.JPG
After the initial pass, the size of the saw/bar and my sharpening skills were really put to the test. This is where I will invest a bit more cash into it (but it still is only a hobby, so can't really justify it straight away), but will really work on my sharpening skills as I'm sure it could have been quicker if my skills with a file were better.
We managed to get through about 3 logs in 5 hours. Given it was our first real attempt at it, I think it was reasonable going. I managed to cut most of the heartwood out in a single hit so I'm assuming those slabs will be throw away jobs, but thinking about it, cypress posts are generally cut from the heart, so maybe they'll be fine.
Anyways, enough of my ramblings, but i'll include a few more action shots, and the final haul for the day.
IMGP7007.JPGIMGP7017.JPGIMGP7042.JPGIMGP7039.JPGIMGP7037.JPGIMGP7044.JPGIMGP7025.JPGIMGP7051.JPG
Oh, I'm the balding fellow in the yellow, the trusty BIL, Adam, has the ginge tinge....
Cheers all
Gabriel
P.S.
Thanks Mum for all the action shots!! (I think the olds had almost as much fun watching as we had doing)"All the gear and no idea"
-
4th January 2016 10:52 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
4th January 2016, 11:09 PM #2
Congrats Gabriel
Well done
Be proud of what you have achieved on your first milling attempt
Great to see all those willing helpers too
B.T.W your 'heart' slabs are quarter sawn...DON'T be throwing them away
Thanks for sharing...MMMapleman
-
5th January 2016, 01:07 AM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,792
Great first effort. well done.
A few tips.
- slope the log downwards so u are cutting downhill.
- wear some eye protection -chips of sawdust doing 100 km/he can still damage eyes.
-
5th January 2016, 10:32 AM #4Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Good to see Gabriel!! And a great result!!!
-
5th January 2016, 11:28 AM #5Novice
- Join Date
- Dec 2015
- Location
- Sierra Nevada Mountains
- Posts
- 10
Good job for your first go! As BobL said, sloping the log will help a lot. Seal the ends of your slabs as soon as possible to minimize splitting.
I see a 90cc saw in your future.
-
5th January 2016, 11:38 AM #6
Thanks for sharing. I have some bulloak to mill
Dave TTC
Turning Wood Into Art
-
5th January 2016, 12:54 PM #7
Very interesting read, thank you for sharing.
-
5th January 2016, 04:08 PM #8SENIOR MEMBER
- Join Date
- Oct 2011
- Location
- Langwarrin
- Age
- 43
- Posts
- 952
If you have a saw/chain that can handle it I am happy to throw the mill in the ute for Austday, but I don't think the little workhorse will be up to the task... it started struggling with pine!!!
Thanks all for the positive comments. I know much better than not wearing eye protection, and now have myself a mesh face guard with earmuffs attached.... was just one of those things on the day (which isn't an excuse, and wouldn't grow back an eye if an accident happened). The downslope sounds like a ripper idea, and given I still have about 10 logs up there to get through, I'll adopt that theory.
Now to hit up the farmers in the area with blackwood!!
Cheers all
Gab"All the gear and no idea"
-
5th January 2016, 04:31 PM #9
I'll have to put the word out for a saw. See how we go
Dave TTC
Turning Wood Into Art
-
5th January 2016, 05:49 PM #10
Wow Gap
What a awesome right up great shots to
And you even have some timber to prove the fact now
Well done mate
Matt
-
22nd September 2016, 03:19 PM #11New Member
- Join Date
- Sep 2016
- Location
- Melbourne
- Posts
- 1
This is a great post. We are about to mill a cypress pine in Lilydale, Melbourne and we are relatively new at milling. We have rigged up an Alaskan saw mill which we have used on a couple of red gums but just wondered how your cypress went a few months down the track. How did you dry the slabs? Did you treat them with anything to stop cracking? I read that cypress dried quickly, has yours dried already? Thank you!
-
22nd September 2016, 03:58 PM #12SENIOR MEMBER
- Join Date
- Oct 2011
- Location
- Langwarrin
- Age
- 43
- Posts
- 952
To be honest I haven't looked yet.... we put end grain sealer over the end grain and stacked it in a shed with 15mm gaps between each board....
Guess I better look....."All the gear and no idea"
Similar Threads
-
Cypress Pine Box
By yosam in forum BANDSAWN BOXESReplies: 5Last Post: 4th June 2012, 03:22 PM -
Dereks Cypress Mill
By derekh in forum SMALL TIMBER MILLINGReplies: 5Last Post: 30th October 2008, 09:19 AM -
Cypress pine
By thefixer in forum WOODTURNING - GENERALReplies: 19Last Post: 5th December 2007, 04:22 PM -
Cypress Pine???
By mcchaddy in forum TIMBERReplies: 3Last Post: 20th September 2006, 12:00 AM