Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 18
-
13th October 2011, 01:15 PM #1Intermediate Member
- Join Date
- Aug 2011
- Location
- Gold Coast
- Posts
- 37
Small Diameter Macadamia- How to mill?
Hi all, I have just cut down a 7m tall macadamia nut tree with a trunk around 200mm in Dia. The end grain timber looks nice so I would like to mill it up to see what comes of it.
I have the following tools available to me:
Chain Saw(s) (Commercial grade)
Drop saw (Commercial grade)
Band Saw (Domestic grade)
I'll try to get a pic or 2 up today.
Cheers in advnce for your advice.
Will
-
13th October 2011 01:15 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
13th October 2011, 01:38 PM #2
Can't help on how to mill it but theres a few nice little bowls in that stump
It's only a mistake if you don't learn from it.
-
13th October 2011, 01:45 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,829
Milling a 200 mm diam tree will unfortunately turn far too much of it into sawdust. Even if it 7m tall I doubt the trunk will be more than about 2-3 m long
The next question is what do you want to do with it? If you want to mill it into boards a Band Saw will do it provided you have help and the bandsaw is big enough and you have the right blade.
So what exactly are your BS specs?
To rip long pieces you will need something like a 1" wide 1 - 1.5 TPI - is this feasible for your BS.
Even with help, just passing a log of this size log thru a BS and hoping for a straight cut is unlikely and asking for trouble so before ripping it you may also want to dock the trunk into more manageable lengths. Even with help i usually stick to 1.8 m lengths or shorter.
One danger of passing a cylindrically shaped object lengthwise through a BS is that the object will roll side ways and jam and break the blade so the way I rip these logs in half with a BS is to get myself a some chip board or MDF with a straight edge about as long and a bit wider than the log. I snap a chalk line along the middle of both sides of the board and place the board on top of the log with the line running along the length of the log and tek screw the board to the log with the tek screws 1" or more away from the line. Then I set up the fence so the BS will cut on or close to the line and with the aid of a helper run the MDF (with log attached) straight edge up against BS fence thru the BS.
Don't expect it to be a fast process, just take it slow and steady and you will eventually get there.
This can be repeated on both halves to create a straight 90º cut to the first rip and from there onwards no MDF should be required. The nuisance is that this method uses up chipboard or MDF very quickly and unless the log is of some value (which a macadamia will be) then it may not be worth it. If you plan to do this often you may wish to set up a proper resawing jig, I think PJT has one of the best on the forum.
-
13th October 2011, 02:36 PM #4
Run some through the band saw but don't waste lots of time & money on it 'cos Maca splits badly.
Cliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
13th October 2011, 03:09 PM #5Intermediate Member
- Join Date
- Aug 2011
- Location
- Gold Coast
- Posts
- 37
Thanks guys,
There are a few more lengths about 2m long ea.
I have no real plans for the timber. I would much rather see it get used to some capacity rather than being burnt or rot away.
I may put a few edges on it with the chainsaw so it at least sits relatively flat.
I have a press which I could use like a giant clamp to hold the logs (max length 400mm) in place while I trim the sides off like a butcher carving meat off the bone so to speak. This would keep the logs secure and the chainsaw away from my legs which is always a good point.
I just found a circular saw in the shed also that could come in handy.
Will
-
13th October 2011, 05:31 PM #6.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,829
If I have plenty of small logs to work with or small burls, I sometimes use this mini chainsaw mill/rig.
paperbark2 - YouTube
The rig holds the small logs firmly in place while the saw and mill cuts the log.
The Saw is a Stihl 441 with a 25" bar with a max cut width of ~20" while chain is lopro 3/8 which has slightly smaller kerf than regular 3/8.
It's a fun gizmo to use - log lengths are limited to < 1.5m.
I can also used the small chains mill without the rig on logs of virtually any length.
If you quarter the log as soon as possible it will reduce the chances of it splitting more than necessary.
-
14th October 2011, 09:23 AM #7Intermediate Member
- Join Date
- Aug 2011
- Location
- Gold Coast
- Posts
- 37
-
14th October 2011, 11:29 AM #8Neil____________________________________________Every day presents an opportunity to learn something new
-
14th October 2011, 11:56 AM #9.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,829
-
15th October 2011, 01:07 AM #10
Hi Will, I'd at least halve them down the middle with the chainsaw and maybe even halve again (so u have four 1/4's), if I was to do them here I would cut a 2" board right out of the middle edge to edge then cut the bark off and cut the pith out then just cut the remainder into 1" wide boards, probably only get a few, whatever you do with it as Cliff says it will crack badly so from green I would try a slow dry, seal the ends, narrow stickers, if you have got somewhere that stays cool and maybe even a bit humid stack them there, under the house in preference to a hot dry carport, the caution there tho is you need to check for mould, you may need to promote a bit of air movement.
Pete
PS forgot to mention it comes up a nice purple and is a fairly hard dense timber when dry
-
21st December 2011, 10:14 AM #11Intermediate Member
- Join Date
- Aug 2011
- Location
- Gold Coast
- Posts
- 37
Milling up now
I finally got around to doing something with the stump.
I took to it with my trusty little chainsaw. I found a Band saw in the in'laws shed still in its box and also purchased a Wagner safe-t-planner off this forum. I should be able to do something with the timber now.
Just got to finish the chain sawing first.
-
21st December 2011, 07:21 PM #12
Hey Will, from your first picture, the timber will give really nice quartersawn grain - so the way we sliced your Spotty was backsawn, you will need to 'turn the boards 90 deg' to make then quarter sawn. good luck
I love my Lucas!! ...just ask me!
Allan.
-
22nd December 2011, 09:00 AM #13Intermediate Member
- Join Date
- Aug 2011
- Location
- Gold Coast
- Posts
- 37
-
22nd December 2011, 12:28 PM #14Intermediate Member
- Join Date
- Aug 2011
- Location
- Gold Coast
- Posts
- 37
Stump is off
I finished off the chainsawing today.
I am reasonably pleased with the results.
The timber looks nice too.
Will
-
22nd December 2011, 12:46 PM #15Intermediate Member
- Join Date
- Aug 2011
- Location
- Gold Coast
- Posts
- 37
Step 2
Now that the stump is off and in the shed to dry out I am going to hit it with the electric planer to tidy up the sides and remove the remaining bark etc.
Then it will be the Drop saw to each end and finally some paint to try and prevent the previously mentyioned spliting.
Should I paint it now???????
Will
Similar Threads
-
Dust extraction - here's a cheap small diameter hose source
By Master Splinter in forum DUST EXTRACTIONReplies: 0Last Post: 28th December 2008, 08:46 PM -
Diameter of small Gifkins dovetail cutter
By sbolton in forum ROUTER JIGSReplies: 5Last Post: 29th November 2007, 05:21 PM -
alaskan small log mill
By weisyboy in forum SMALL TIMBER MILLINGReplies: 52Last Post: 14th June 2007, 06:31 PM -
Small Diameter Red Cedar Logs
By Bob Whitworth in forum TIMBERReplies: 4Last Post: 29th September 2006, 08:58 PM -
How to hold small diameter stuff
By Tiger in forum WOODTURNING - GENERALReplies: 4Last Post: 12th February 2006, 09:20 AM