Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Up grade
-
31st January 2016, 04:27 PM #1New Member
- Join Date
- Oct 2015
- Location
- Mossman north quensland
- Posts
- 4
Up grade
Hi all just upgraded my Alaskan and 090s to a new Lucas 10-30efi .shold have done it a few years a go can as I can not falt the mashine eny tips or tricks yous old times can tell me for sawing on hills ???
-
31st January 2016 04:27 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
1st February 2016, 10:40 PM #2
-
2nd February 2016, 06:41 AM #3GOLD MEMBER
- Join Date
- Jan 2013
- Location
- the sawdust factory, FNQ
- Posts
- 1,051
There's hills and theres Hills.
Here's an old thread on the topic here: Milling on a hill
The general consensus is avoid where possible, but it can be done, Best bet is always to avoid it where you can and be very bloody careful. Also think about the effort vs reward curve carefully... you need to be seeing serious money coming off saw to make it worth the effort.
If you're going to be doing it put a set of feet under the mill like the attached picture. It'll give you a better range of height adjustment for getting the rails parallel. Put a hole in the foot part and put pins through them - stops the mill from trying to walk downslope as you're working.
Best advice though is "buy a bigger bulldozer".
-
2nd February 2016, 12:16 PM #4Novice
- Join Date
- Dec 2015
- Location
- Sierra Nevada Mountains
- Posts
- 10
Milling down a hill is easy with the alaskan mill!
What are your plans for the 090? Don't see many around anymore.
-
2nd February 2016, 01:46 PM #5GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
Slopes are for skiing.
-
2nd February 2016, 04:36 PM #6
My point exactly Rustynail
Doesn't matter one iota how much money one could make either
For the 'heroes' out there that think it's o.k...i'll tell you it isn't!
Irresponsible and utter stupidity for mine
Think SAFETY people....chainsaws and mills CAN and DO kill folk...treat them with the respect that they deserve...MMMapleman
-
2nd February 2016, 10:54 PM #7GOLD MEMBER
- Join Date
- Dec 2010
- Location
- Mornington Peninsula
- Posts
- 2,746
It was said previously - stay away from milling on slopes!
-
3rd February 2016, 11:35 AM #8GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
Looking back over the forty years spent in the timber industry, I can say that most site accidents were on sloping ground. Of course that doesnt include fixed mill accidents as fixed mills are on level sites, with only a drainage slope to contend with.
Lucas mills will operate at 30 degrees. That's great for the mill, but not so good for the operator. With a portable mill, the temptation to set up on less than level sites is a real one, but after seeing and hearing of mishaps, one tends to look for better alternatives.
Many is the log I have had to go to no end of trouble to get to level ground. I just see it as a necessary evil - Part of the process.
Similar Threads
-
Box up grade for the son
By rusel in forum CNC MachinesReplies: 8Last Post: 18th August 2014, 09:19 PM -
Grade 12 project
By Freddo in forum WOODWORK - GENERALReplies: 14Last Post: 27th April 2006, 04:08 PM -
Utility Grade
By Tex B in forum TIMBERReplies: 3Last Post: 14th November 2005, 12:36 PM -
AA grade Birch Ply
By MICKYG in forum TIMBERReplies: 0Last Post: 13th November 2005, 07:18 PM