Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
2nd April 2015, 05:03 PM #1Intermediate Member
- Join Date
- Jan 2013
- Location
- Bendigo, Victoria
- Posts
- 44
Milling an ELM TREE in Bendigo (VIC)
G'day,
For those who are familiar with Bendigo (central Vic), you would've seen a huge population of lovely mature Elm trees all over the place.
I just happen to be fortunate enough to have a monster in my front yard, BUT - and I'm quite sad about this - it's become victim to 'elm beetle' disease and has died. I've had a couple inspect the tree and they've all confirmed the sad news.
Having said that, I'm super keen to get my chainsaw mill into it when I get it cut down. I've never milled an Elm before, and have only seen photos of Elm slabs on the Internet.
Any comments / experiences / suggestions around slabbing Elm? Is it worth the effort? Has anyone around Bendigo slabbed an Elm?
Look forward to your input...
thanks in advance. Phil.
-
2nd April 2015 05:03 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd April 2015, 11:45 PM #2
In 2012 when the local council (Ballarat) dropped a few Elms along the Avenue of Honor in preparation for the 100 years ANZAC shindig, I grabbed a few trunks that they had left lying on the roadside for a couple of weeks (nay...not grabbed...rather, saved from the chipper) and slabbed them at about 70mm thick. Left them to air dry and have quite literally, only in the last month, started sawing them down to size and climatising (sp) for use in a hallway bench seat project.
I've never used Elm before but these bits look lovely. A nice brownish color and these particular pieces have a simple and pleasant grain/ring pattern in them.
The slabs were end-sealed simply with paint and haven't split much at all. There are a few small knots that have opened up but that's what you get.
I'll try to remember to post some pics tomorrow night of the "refined" boards and a few of the slabs I still have in their "fresh from my shoddy home made Alaskan mill for a 22" bar" form
I figure: whatever the timber, if you can get some boards from it, it's worth it. So get milling and get those puppies drying
EDIT: Oh, and I also took notes of which soldiers these trees were dedicated to. While the old ones have since been replaced, I thought that it would be respectful to be able to note the history and dedication behind the timber used in my projects. I did contact the council before I took them, but they were extremely slow in responding so I went with my gut on "saving" the logs from an otherwise useless and less considerate purpose. Which was fortunate, because not long after, the bits I left behind were removed.Every time you make a typo, the errorists win.
-
3rd April 2015, 10:45 AM #3GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
Elm is well worth the trouble. Our dear forum friend Woodward was very fond of it for furniture making.
Don't cut too thin as it can be prone to cupping. Sticker tight and close to the ends. Air dry slowly.
-
3rd April 2015, 07:12 PM #4Intermediate Member
- Join Date
- Jan 2013
- Location
- Bendigo, Victoria
- Posts
- 44
Thanks for the replies!
At it's thickest, the trunk section (which should be about 3m long when felled) is about 650mm diameter. Thanks for the advice re cutting the slabs a bit thicker...
There's also a few big branches that might slab up nicely, or perhaps they'd enjoy going through a bandsaw...
Will keep y'all posted and post some pics when it comes down.
Phil
-
3rd April 2015, 08:09 PM #5GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
Elm branches tend to make very unstable timber.
-
4th April 2015, 12:00 PM #6
The Tree.
Hi Phil,
Seeing that Woodturners Bendigo, have their Wood Show on, why not approach them.
There are some very experienced Woodies there.Regards,
issatree.
Have Lathe, Wood Travel.
-
4th April 2015, 01:12 PM #7
Hi.
I slabbed 3 or 4 Bendigo Elms about 30 years ago.
The rot caused by the beetle infection leaves a very nasty sludge inside. Make sure you clean or cut that out thoroughly or it will spread.
It is a lovely timber and I made quite a few pieces of furniture out of mine. Still have some of it left too.
Be aware that the city council has a log contract and may not just 'give it ' to you - if it is on the nature strip , it belongs to the city....Cheers,
Joe
9"thicknesser/planer, 12" bench saw, 2Hp Dusty, 5/8" Drill press, 10" Makita drop saw, 2Hp Makita outer, the usual power tools and carpentry hand tools...
-
4th April 2015, 08:17 PM #8
Heh...I've been caught out with that twice before. The first time was fair and square, but it was the a neighbour out bush (who commissioned the felling) that got the warning. Second time was for a claret ash (we had planted in our own front lawn 30 years before) that BARELY encroached on the nature strip (I'm talking the thickness of the bark) and yet they came out to tell me off.
*meh* Got some great pieces out of it
Anyhoo, here's one of the smaller roughly cut down sticks from the elm I collected. The photo color isn't great, but the timber is nice light brown and once it's smoothed and has a finish applied, it should look fantastic.Every time you make a typo, the errorists win.
-
5th April 2015, 04:53 PM #9Intermediate Member
- Join Date
- Jan 2013
- Location
- Bendigo, Victoria
- Posts
- 44
Thanks for the advice re the Elm branches. I'll look closely before considering slabbing them or possibly putting them through the bandsaw.
My tree is well and truly on my property, but will still make some 'anonymous' queries with council around regulations, etc...
Similar Threads
-
milling for a tree lopper
By weisyboy in forum SMALL TIMBER MILLINGReplies: 2Last Post: 11th November 2013, 07:52 AM -
Milling an Apple Tree for Tool Handles
By DJ’s Timber in forum HAND TOOLS - UNPOWEREDReplies: 9Last Post: 14th June 2013, 12:36 AM -
FREE labor - Bendigo bloke seeking milling experience with a LUCASMILL
By PhilthyMills in forum SMALL TIMBER MILLINGReplies: 0Last Post: 5th January 2013, 12:36 PM -
Plain tree milling
By Stewy in forum SMALL TIMBER MILLINGReplies: 5Last Post: 15th October 2012, 08:10 AM -
milling my tree
By aussiecolector in forum WOODIES JOKESReplies: 1Last Post: 22nd July 2005, 08:51 PM