Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Milling a Marri log
-
15th March 2012, 04:45 PM #1New Member
- Join Date
- Mar 2012
- Location
- Kensington, WA.
- Posts
- 2
Milling a Marri log
Hi all,
I've just had a large marri in my back yard cut down, and want to find someone to mill the timber. I've had advice to seal the ends with paint and will do this asap.
The top of the tree was dead, brittle and large branches looked diseased and were falling down daily, but the bottom of the trunk looks good. It measures 700mm x 2440mm, and is currently lying on brick paving. We would like to use the timber to build either a bench seat or bar.
I want to know if someone will come and mill this at my house in Kensington. There is access to the backyard through a garage, and there is probably enough space to work in. We are keen to make the most of this timber, but if it is going to cost a fortune it might not be possible.
I'm interested to know if this is a worthwhile project, and appreciate your advice.
Cheers, Lisa
-
15th March 2012 04:45 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th March 2012, 06:36 PM #2SENIOR MEMBER
- Join Date
- Dec 2007
- Location
- Gold Coast
- Age
- 63
- Posts
- 847
Hi Lisa and welcome,
The obvious question is : which Kensington ?
d.
-
15th March 2012, 07:20 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,812
If it's Kensington in WA I am real close by and can at least come and have a look at it and give you some advice. PM me of you want to.
-
16th March 2012, 01:05 PM #4New Member
- Join Date
- Mar 2012
- Location
- Kensington, WA.
- Posts
- 2
Dabbler, sorry about that, it's Kensington WA.
Thanks BobL, I have sent a pm.
Lisa
-
16th March 2012, 10:28 PM #5SENIOR MEMBER
- Join Date
- Jan 2009
- Location
- Busselton, WA
- Posts
- 708
Even though its fresh down that looks real nice, keep us posted Bob
-
16th March 2012, 11:46 PM #6.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,812
Went around and had a look and dropped off some end sealer. Nice little log, bit of a bend to it but I should be able to get something decent out of it. I don't think it's a marri but a WA river red gum. Targeting to do it on Good Friday.
Similar Threads
-
About time to see some milling on the small milling forum!
By Sigidi in forum SMALL TIMBER MILLINGReplies: 16Last Post: 21st December 2011, 07:22 PM -
Where to get Marri
By Whit68 in forum TIMBERReplies: 2Last Post: 9th May 2011, 10:26 AM -
More WA Marri
By Burnsy in forum SMALL TIMBER MILLINGReplies: 27Last Post: 15th June 2009, 07:24 PM -
Marri Box
By GRS in forum WOODWORK PICSReplies: 13Last Post: 19th August 2005, 08:07 PM -
Help on milling marri!
By ajaj in forum TIMBERReplies: 0Last Post: 10th August 2005, 10:28 PM