Thread: Milling Raintree questions

I was not familiar with Raintree, but from Bootle's "Wood in Australia," it is a hardwood that is native to central America. It weighs in at around 560kg/m³ so not very dense: Lighter than Silky Oak and Cypress Pine to give some comparison.

Small logs that are cut from top to bottom will be subject to spring and may be unusable for slabs. You will have to give it a go to see how it behaves. The rule of thumb for cutting smaller logs is to cut down to one third of the diameter and then rotate 90°. This does two things: It minimises the spring in the timber (that will produce bananas) and it allows the blade to enter clean wood. Again the log is cut down to two thirds before rotating again. This process is followed until a square baulk remains.

If you are cutting a larger log for slabs and the tree had reached maturity the spring growth may have gone. However, as the cuts progress down the log the cuts that incorporate the heart will not be useable full width as the heart degrades. I am not familiar with the timber so cannot offer advice for slab thickness. Anything around 50mm to 75mm is typical for slab material. The log ends should be sealed (immediately) and stacked for drying carefully with stickers.

Regards
Paul

"Samanea Saman" also known as Monkey pod. You can treat it the same way as you would Australian Red Cedar. In other words, saw for figure (through and through) very stable, insect resistant and durable. Slabs will stay pretty flat even when back sawn. Easy to dry. I've cut a lot of it over the years and have never had a problem with it.

You MUST treat the sapwood
Borers love it!!
Lovely timber well worth milling imo
Log Dog

Originally Posted by Brian45

what is a good moisture meter as I would like to get a reading when we cut so as to monitor over time.

A good moisture meter is a pinless Wagner but you'll need to fork out over $500
see Wagner Moisture Meters
These will give you the closest to absolute moisture content (MC) but all MC meters nee to have their readings "fudged" to suit the specific type of timber being tested. Some have built inc corrections for common timber but I'll bet Money pod won't be on the list.

However if you want to just know "approx" MC or "relative" (how different is the MC of this bit of [the same type of] wood to that one) then most of the pin type budget meters will do that. These meters are also less accurate at very higher and low MCs.

Accuracy of MC measurement has often more to do with measurement technique than the type of meter. You cannot walk up to a pack or stack of timber and make one measurement to a piece of wood on the outside of the pack and assume the rest of the pack is the same. Multiple measurements are needed including from pieces inside the pack and even inside they pieces of woo wood open! A pinless will help avoid the need to cut pieces but you will still need to split the pack. Just a quick poke of the surface can be very misleading - I drill holes into (especially hard) woods so the pins can penetrate as far as possible into the wood.

I bought cheap Digitech >20 years ago and I think it cost me about $60 and note that last year these were on sale everywhere for ~$20 an are no longer available or at least I can't see any for sale..
Screen Shot 2022-06-12 at 6.05.08 am.jpg

Digitech have replaced these with a new meter that costs around $40, they probably still use the same circuits inside them
Pocket Moisture Level Meter for wood & Building materials 9319236235355 | eBay

It looks like the original Digitech MCs are still being made under another name (CEM) and being flogged on ebay for $200!
A● CEM DT-125 Mini Portable Digital Timber Wood Moisture Level Meter Tester | eBay
Buyer beware!

Originally Posted by rustynail

"Samanea Saman" also known as Monkey pod. You can treat it the same way as you would Australian Red Cedar. In other words, saw for figure (through and through) very stable, insect resistant and durable. Slabs will stay pretty flat even when back sawn. Easy to dry. I've cut a lot of it over the years and have never had a problem with it.

Well the plan at this stage is to just cut the slabs and stack with spaces and weigh the stack down. Take a moisture reading at various sections along the slabs and monitor over time. The humidity up here will have a bearing as well.

If nothing else will be interesting.

Originally Posted by Log Dog

You MUST treat the sapwood
Borers love it!!
Lovely timber well worth milling imo
Log Dog

I just let the borers have the sapwood. Same with Red Cedar. I never put sapwood into furniture as it defeats the purpose of using a durable timber.

Originally Posted by rustynail

I just let the borers have the sapwood. Same with Red Cedar. I never put sapwood into furniture as it defeats the purpose of using a durable timber.

Each to their own!
I never allow borers into my shed
They will also attack the heartwood at times
Anyway the contrast of sapwood against a dark timber can be quite appealing
Particularly in bowls and fancy turnery
Can look good in furniture too depending on the style
Log Dog

Raintree is a lovely timber, good to work with, however, it is a bit acrid on the nose when dry. As has been mentioned, the sapwood is susceptible to borers.

Jim

Don't know about the milling, but, having worked with it dry, my only advice is be very careful about the dust. This is by a country mile the most brutal dust I've ever come across, and by that I mean sticking your head into a room full of ammonia and sniffing up a pinch of ground pepper kinda brutal.

Yes, you need a respirator when sanding this timber.

Originally Posted by Log Dog

Each to their own!
I never allow borers into my shed
They will also attack the heartwood at times
Anyway the contrast of sapwood against a dark timber can be quite appealing
Particularly in bowls and fancy turnery
Can look good in furniture too depending on the style
Log Dog

Yes, you guys have some nasty little critters up that way. We only have to contend with Lyctus and Termites. I should also mention I am very choosy about the species I am prepaired to put into storage.

Originally Posted by rustynail

Yes, you need a respirator when sanding this timber.

If sanding is being done inside a shed then it sounds like some form of extraction would also be needed otherwise it's just going to contaminate the whole shed. If it affects breathing the PM2.5 is also going to get thru skin and eyes. Then there's the issue of getting all over clothes and carried around until clothing is removed.

Just reading some of the comments on this post about health issues working with Raintree and thinking to myself that I don't recall having experienced them (42 years ago and in ancient conditions) or now and I'm 72 and healthy as.

Back in about 1978 I made two conference tables (as per picture) from Raintree over about a 5 month period. At the time I worked for Forestry, Fisheries and Wildlife at Berrimah Farm in Darwin. This was also the only government run joinery shop in the NT. It was also the time when the NT was changing to statehood. Directions and details came down from the powers that be to make a conference table for the new government's cabinet room. The top is as per the supplied details, but the two legged base is my design. In the original design the top was to sit on a four legged aluminium base which I thought was ridiculous and would not suit the top. I stated this to my boss to which he said give me a design to present to the powers that be... the result being in the attached photo. That was the first one. The second one was made after Malcom Frasier came to declare statehood seen the table and requested one for Tammy's Australiana project.

Originally Posted by rod1949

The second one was made after Malcom Frasier came to declare statehood seen the table and requested one for Tammy's Australiana project.

It's a pity more individuals/corporations/businesses with power/money don't request this sort of thing. I also think of every news desk, morning/afternoon/sevening/current affairs show desks etc on TV etc. Instead of being made of crappy plastic they should all be made of natural materials like native Aussie timber.

Where dust is concerned I'm wary of statements like "I worked with X all my like and I'm fit and healthy" as it reminds me of "I smoked all my life . . . . ."
Like diets, dust affects people differently so I don't doubt that some people can work in very dusty conditions for very long periods and get away with but the healthy impact of ANY fine dust are compelling.

As for being fit and healthy at 72 - Good luck to you about that but according to my GP that just means you haven't been probed long and hard enough