Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Cypress Pine - Drying methods?
-
13th February 2013, 09:06 PM #1Member
- Join Date
- Apr 2009
- Location
- brisbane, australia
- Age
- 58
- Posts
- 87
Cypress Pine - Drying methods?
Hi All,
I have searched this forum pretty thoroughly to see if there is anything like a thread that deals with drying timbers....specifically Cypress Pine. I've managed to get my hands on a couple of lengths of Cypress Pine. Diameter ranges from 40-45cm. Length approximately 1500mm. The tree had fallen over in the latest Brisbane storms about 3 weeks ago - but i was only able to cut out the pieces I wanted today.
Is there a concencus on the best way of drying this timber? Should I leave it in one piece to dry? or should I cut the logs into planks? say 50mm thick, sticker the planks and paint the ends etc??...or is that going too far????...anyone have any gems of wisdom on this issue???
IMAG0553.jpghere are the pieces in question....
-
13th February 2013 09:06 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
13th February 2013, 09:53 PM #2
Cypress is more stable than others, but I dry in exactly the same way as any other timber. Cut as small as possible for future use, seal ends and stack properly to dry with suitable stickers etc
Neil____________________________________________Every day presents an opportunity to learn something new
-
14th February 2013, 11:49 AM #3
On other important thing is to split them down the middle, through the heart to to minimise star shakes.
- Andy Mc
-
14th February 2013, 12:00 PM #4Member
- Join Date
- Apr 2009
- Location
- brisbane, australia
- Age
- 58
- Posts
- 87
thanks for the comments......i'll get onto it ASAP
-
14th February 2013, 08:34 PM #5GOLD MEMBER
- Join Date
- Jan 2013
- Location
- the sawdust factory, FNQ
- Posts
- 1,051
Cypress gets brittle at low M/C's. When running it for flooring we tend to mould green off saw as otherwise it has a propensity to chip out. Shrinkage rates are low (2.5% radial, 3% tangental) so it's possible to do that. I don't know about regular planing however suspect it would be inclined to chip out along the arris when dressed if dry.
It also develops fine surface checking on the dressed surfaces so it's best to slow the drying rate down as much as possible during the initial stages of drying in hot weather. Stack under cover, use thinner stickers when stripping out, seal the ends, try and reduce airflow through the stacks, etc etc. Once the moisture level drops it should be fine though.
-
15th February 2013, 03:04 PM #6Member
- Join Date
- Apr 2009
- Location
- brisbane, australia
- Age
- 58
- Posts
- 87
-
18th March 2013, 10:34 AM #7New Member
- Join Date
- Jan 2012
- Location
- Adelaide SA
- Posts
- 1
-
18th March 2013, 10:55 AM #8Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Stickers are the lengths of timber used to separate the layers in stacked timber. They
allow air flow around the stack.
About 20mm wide and 12-15mm tick is enough. With those length logs one either end
and 2 more evenly spaced between them will do the job.
-
1st April 2013, 08:22 PM #9New Member
- Join Date
- Mar 2013
- Location
- Sunshine Coast ,QLD
- Posts
- 4
Very helpful information there and quite timely as I was going to ask the same thing last night regarding drying Camphor Laurel and Pepper tree wood. I intended to cut it insitu with a chainsaw into slabs 25 - 50 mm thick then dry it undercover with stickers so on the right track. One question - What kind of sealer do I use to seal the ends. The timber is to be used for lure making and eventually cut into 50 - 80 mm lengths by 25 mm thick for hand carving. Cheers Pat.
-
25th July 2013, 09:27 AM #10GOLD MEMBER
- Join Date
- Nov 2012
- Location
- Brisbane
- Posts
- 1,809
Just found this thread and see you haven't had an answer. I'm not expert but can give some starting information if you still need it. End grain sealers seem to come in different types and I have used a wax based one (made by Mobil I think) many years ago that worked well drying a big stick of NSW Rosewood (200 x 200 x 4m). It took years. I haven't had to dry anything for 25 years but have just been gifted a section of a River Blue Gum log. Eucalyptus teretecornis that is. So have done some searches and found that Carba-Tec sell an end grain sealer that sounds similar to the type of sealer I used years ago. I haven't tried it but am going to make the trek across Brisbane to purchase some and try it out.
Commercial millers talk about using paint but I don't know what types. I am sure that other forum members will have experience on end grain sealers that they can share.
-
1st August 2013, 05:44 PM #11Senior Member
- Join Date
- Apr 2010
- Location
- Adelaide
- Posts
- 191
When I went past the Timber Mill in Strahan I thought I spyed an electric frypan full of beeswax, that I figured they were using to seal the ends of some of the slabs etc that they were cutting out.... Others may know more though. I'll have some Cypress to dry out soon too.
Similar Threads
-
Cypress Pine Box
By yosam in forum BANDSAWN BOXESReplies: 5Last Post: 4th June 2012, 03:22 PM -
Cypress Pine
By Les in Red Deer in forum WOODTURNING - PEN TURNINGReplies: 7Last Post: 3rd November 2008, 10:00 PM -
Cypress pine
By thefixer in forum WOODTURNING - GENERALReplies: 19Last Post: 5th December 2007, 04:22 PM -
Cypress Pine
By Doug Pankhurst in forum TIMBERReplies: 0Last Post: 3rd March 2000, 09:38 PM