Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
-
9th April 2008, 11:56 AM #1Novice
- Join Date
- Apr 2008
- Location
- Sydney
- Posts
- 10
Ideas for replacing rotten Oregon
I'm trying to replace some rotten exterior oregon with either treated pine or hardwood, as recommended by the good people on this forum.
I'm having trouble finding the right stuff. The existing Oregon is rough sawn, so I've been looking for some treated pine or hardwood that has the following features:
- kiln dried (KD) or seasoned
- rough sawn
- 220 x 50 x 5.5M (or close)
- NOT rough headed if treated pine
- NOT dressed if hardwood
Does anyone have any ideas? I've spoken with lots of timber yards and they all say that there is no KD treated pine in that size that isn't rough headed or dressed, and no KD hardwood that isn't dressed.
Any assistance appreciated.
roice
-
9th April 2008 11:56 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
9th April 2008, 02:32 PM #2
Roice,
If it is for external application then there is no advantage in KD timber as it will take up moisture again in any case. Treated pine is submerged in the preserving liquid under pressure and can be wringing wet when you get it. Just stack it flat with stickers to allow air flow over the wood for a few weeks before use. If you can source dry stuff at a yard then better.
If you are replacing rotten untreated wood with treated the chances are that the rest of the untreated wood will rot also. Oregon has to be protected from the elements. Depending on the dimentions you need treated for fencing is usually just sawn. There are a few pine places that will cut to you'r requirements. Check yellow pages for timber.
Regards
John
-
9th April 2008, 03:02 PM #3Novice
- Join Date
- Apr 2008
- Location
- Sydney
- Posts
- 10
Thanks John. My concern is that unseasoned pine will warp. I had a bad experience with some green sleepers once.
The new timbers will be a fascia that supports a gutter system around the edge of the house, so any movement once in place will be disastrous.
roice
-
9th April 2008, 04:27 PM #4Old Chippy
- Join Date
- Mar 2007
- Location
- Canberra
- Age
- 72
- Posts
- 394
Usually you will not have the sort of twisting and distortion that you experienced with treated pine sleepers when you use structurally graded treated pine beams. The sleepers are often centre wood or from timber that is unsuitable for structural grading - they have many flaws with large knots etc.
Best if you select yourself or get someone to do it for you, but that size and dimension should be widely available and remain stable when used.
Hardwood too would be OK, but again would need to be selected for straightness and grain direction or you will have problems.
In either case if you leave it unprotected you have higher chance of twisting, bending or other distortion so oiling or painting can help too.
Similar Threads
-
Replacing old Oregon
By roice in forum TIMBERReplies: 9Last Post: 5th April 2008, 01:37 PM -
rotten wood
By weisyboy in forum SAFETYReplies: 10Last Post: 12th December 2007, 10:55 AM -
It's a rotten job...
By Phil Jennings in forum HAND TOOLS - POWEREDReplies: 12Last Post: 10th October 2003, 04:42 PM -
Rotten Bl****y scraches
By cliff cook in forum FINISHINGReplies: 3Last Post: 9th September 2003, 11:38 PM