Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
-
23rd October 2008, 03:02 PM #1New Member
- Join Date
- Sep 2006
- Location
- Ipswich
- Posts
- 2
Minimum size for milling/slabbing
Hi all,
Long time lurker, first time poster.
We've got a acerage block in Anstead, QLD, that we're planning on building on next year. There's a fair number of trees on the block and we need to clear an area for the building pad.
Before we start I want to check what the minimum diameter log is worth salvaging for milling/slabbing? The biggest trunks are about 500m dia, but there's not very many of them. Timber species are Ironbark, Red Gum, Pink Bloodwood, I think.
Thanks,
Matt
-
23rd October 2008 03:02 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
23rd October 2008, 04:53 PM #2
It depends on a lot of factors.
The type of wood, I'm not familiar with those species, one of the locals can probably advise better.
The quality of the log, A dead straight, little taper or branches log of 200mm may be worth sawing if it's something valuable. But a 500mm knotty banana shaped log is probably better cut into firewood.
Generally, the smaller the log, the lower the quality of the timber, and the more time it takes to saw X number of boards from them. So it eventually gets to the stage where you look at the measly pile of boards it's taken all morning to saw, and decide it wasn't worth it.
But I would say if you have nice straight logs over 300mm on the small end then it's probably worth the effort to get them sawn. I've sawn smaller, but was it worth it.. not really.
Ian
-
24th October 2008, 11:53 AM #3
Matt,
I'm down in Brissy next week, I might be able to come out to Anstead to have a look and give you an idea of what to keep or toss.
Depending on your time frame for works, I offer a service where I'm on-site the day of the clearing, dock up all useable timber from any/all tree's coming down. If this is done while machinery is there, the waste/useless logs/bits can go straight into a waste pile and the useful logs can be stacked ready for milling. This way the machinery is already there and you don't need to get it back later after the useable stuff has been taken from the tree's and you don't have them sprawled across the worksite for a time.
After this the logs can be milled that day if there is time or started the next day, depending on everyones time frames.
Give me a ring using details from my website if you wanted to get together at the block while I'm in Brissy next week.I love my Lucas!! ...just ask me!
Allan.
-
27th October 2008, 12:21 PM #4New Member
- Join Date
- Sep 2006
- Location
- Ipswich
- Posts
- 2
Later in the week will suits best, or even Saturday if you're still down this way, I be at the block most of the day sorting out some drainage issues on the driveway. I'll be in touch the next day or 2 to organise something.
Cheers,
Matt
Similar Threads
-
Minimum top size for LS25"
By Sapling in forum INCRA JIGSReplies: 4Last Post: 13th August 2008, 06:06 PM -
Slabbing logs
By BobR in forum SMALL TIMBER MILLINGReplies: 5Last Post: 26th May 2008, 12:03 PM -
Slabbing Ironbark
By BUNTA in forum SMALL TIMBER MILLINGReplies: 4Last Post: 16th February 2008, 12:05 AM -
Need some slabbing
By DavidG in forum TIMBERReplies: 10Last Post: 25th September 2005, 09:03 PM -
slabbing
By vandavy in forum TIMBERReplies: 4Last Post: 13th December 2004, 01:09 AM