Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: Seasoning tips for exotics
-
12th October 2014, 07:25 AM #1Novice
- Join Date
- Jun 2014
- Location
- Adelaide
- Posts
- 16
Seasoning tips for exotics
Hi there,
I've been reading with interest on the forums for a little while but this is my first post. Whilst I have been woodworking for a while, I only started milling my own timber recently using a chainsaw mill. I have made some good lengths of jacaranda, gum and callistemon. The only problem is I know nothing about drying the wood, seasoning I believe is the correct term, and some nice pieces I had planned for furniture have been left riddled with cracks, cupping and twist. I have been doing some reading online but I'd be grateful for any general tips, recommended books to buy or even if you can mention a blog/post which outlines tips for new players like me..
By way of background I have cut timber into planks and thicker sections and stacked them in a dry/dark/warmer area of my shed. Within weeks large cracks and twist began to form. I'd be interest is any methods used to avoid the cracking in particular.
All feedback is welcome. Thanks
Bill
-
12th October 2014 07:25 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
12th October 2014, 10:22 AM #2.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,793
What are the dimensions of the logs you are cutting and what are the dimensions of the cut pieces.
-
12th October 2014, 02:14 PM #3Novice
- Join Date
- Jun 2014
- Location
- Adelaide
- Posts
- 16
Hi Bob. I have done various lengths and thicknesses. Planks about 1 - 2m long, 20mm wide, thickness 25mm and 40mm. I have also done some slabs and thicker pieces for coffee tables once they have dried. The worst was the jacaranda slabs/pieces which have split badly and some of them have twisted.
-
12th October 2014, 03:20 PM #4.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,793
You didn't say how big the logs are, when they are small and /or were under tension/compression they are likely to cause more probs
I would never cut at 25 mm as this very likely to lead to problems especially if the logs are small.
Unless the timber is near quarter sawn I wouldn't cut anything narrower than 50 mm and where possible cut 62 mm
Are your cut ends sealed, wax/paint/endche?
Close (450mm) space stickering is important.
Stickers much be same size
Stickers MUST be lined up under each other
Always use a sticker on the ends
Add weight or clamping where possible.
No direct sunlight
Warmth is not necessary, the wood will dry even at sub zero temperatures.
Too low a humidity is more likely to lead to splitting - some sort of loose covering helps reduce rapid moisture loss.
-
12th October 2014, 09:46 PM #5
Welcome Bill. Bob is on the right track.
If you place your timber in a warm area they can effectively cook, cracking the timber too. Even the coolest area of the shed can be too hot. High winds, especially hot winds, can also tend to dry the timber too fast. The stack should be ventilated, but not wind blown. The best idea is to dry the timber as slowly as possible.
Interesting you say this Bob. All my smaller pieces up to dia 300mm are cut 25mm thick and up to 0.5m long for pen blanks and boxes. I stack them with ice-cream sticks as stickers at 50-100mm centres and bind them with cable ties back into the log forms to dry. The cable ties are not cut so they can be re-tensioned as necessary.Neil____________________________________________Every day presents an opportunity to learn something new
-
14th October 2014, 08:26 AM #6Novice
- Join Date
- Jun 2014
- Location
- Adelaide
- Posts
- 16
Thanks Bob and dai sensei they are very useful tips. I obviously read the wrong thing as I thought the warmer part of the shed would be more appropriate. I'll need to decide on a cooler area which is still ventilated. Wind wont be a problem.
Dai sensei with the ice cream sticks, do you double them up or is one enough thickness? Also, is it necessary to treat the ends with wax?
The gum and jacaranda I cut were very large trunks, not small at all, but the cracking was quite severe. I'll be more careful with the stickering and add some weight and light covering on future cuts.
Thanks
-
14th October 2014, 09:35 AM #7
-
14th October 2014, 01:55 PM #8Novice
- Join Date
- Jun 2014
- Location
- Adelaide
- Posts
- 16
-
14th October 2014, 03:28 PM #9.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,793
-
14th October 2014, 08:53 PM #10Neil____________________________________________Every day presents an opportunity to learn something new
-
15th October 2014, 08:32 AM #11Novice
- Join Date
- Jun 2014
- Location
- Adelaide
- Posts
- 16
Can either of you give me approximate times for timber to dry? I realise it would depend on the timber but a ball-park figure would give me an idea for smaller stuff 25mm thickness from smaller logs say 10"+ and 50mm thickness from larger logs say 20"+.
Cheers
-
15th October 2014, 11:27 AM #12
The old rule of thumb is 1 year per 25mm of timber exposed. Softwoods like cedar are faster, very close grained hardwoods like Gidgee longer. You can get moisture meters to test but they will only test to the depth of the prongs. I find the best way is cut a piece and hold against your cheek, usually you can then feel any moisture.
Neil____________________________________________Every day presents an opportunity to learn something new
-
15th October 2014, 02:14 PM #13Novice
- Join Date
- Jun 2014
- Location
- Adelaide
- Posts
- 16
Similar Threads
-
a couple of exotics
By mkypenturner in forum WOODTURNING - PEN TURNINGReplies: 12Last Post: 7th June 2011, 09:42 PM -
a couple of exotics
By bench1holio in forum WOODTURNING - PEN TURNINGReplies: 8Last Post: 9th March 2010, 07:59 PM -
help with seasoning
By gavin e in forum WOODTURNING - GENERALReplies: 1Last Post: 4th March 2007, 12:08 AM -
Every tried to import exotics
By MathewA in forum TIMBERReplies: 6Last Post: 6th May 2005, 12:26 PM -
Turning exotics
By KristianH in forum WOODTURNING - GENERALReplies: 5Last Post: 3rd February 2005, 04:32 PM