Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: cutting depth on workcentre
-
18th March 2010, 07:03 PM #1newbie that's keen
- Join Date
- Mar 2007
- Location
- Bonny Hills, NSW
- Age
- 64
- Posts
- 517
cutting depth on workcentre
To all Triton Owners,
after having a cheap Ryobi table combination saw die on me I decided to upgrade and buy some Triton gear. Among other pieces, I bought the Workcentre 2000 and the Triton 235mm saw. The biggest gripe I have (compared to my cheapy Ryobi table saw) was the depth of cut. On the Ryobi, I could rip/cut a piece of wood that was up to around 8cm thick (it was a 10" table saw) but with the Triton I could only rip a piece up to approx. 6cm. In tablesaw mode (as long as I had a flat piece of wood) I could do a little better but was a bit disappointed.
What I am planning is a cross cut sled without the Triton table top to at least give me some more depth when I need it. It will run along the outside of the sides of the Workcentre. I will use either 3mm ply or mdf to give myself maximum cutting depth.
What I would like to know from the community is:
- is what i am doing unsafe?
- what have others done when they have faced this problem? I am not woodworking genius (more like a hacker) so expect that there are some better solutions around!!
My first throught had been to remove the saw and use it without the workcentre but I did not find any good method of making accurate cuts.
All comments and help most appreciated.
Mick
-
18th March 2010 07:03 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
18th March 2010, 07:53 PM #2
Flip it over and use it in crosscut mode. Adjust the table so the blade fully lowered just goes into the groove. You can then cut the full capacity of the blade.
What size saw are you using? [EDIT: Just reread the post - the 235mm saw should cut a fair bit pretty ok in crosscut mode]
Cheers,
Dave
-
18th March 2010, 09:04 PM #3
According to the saw specs:
Motor: 2400W
Speed: 4100 min-1
Blade: 235mm (9in), 40 tooth Triton Premium TCT - 25mm arbor
Cut depth: 0 - 82mm 45 - 61mm
Bevel Adjustment: -1 to 46 Stops at 0, 15, 221/2, 30 & 45
So in cross-cut mode you should manage around 80mm.
Ray
-
19th March 2010, 10:28 AM #4Member
- Join Date
- Apr 2006
- Location
- Roslin, Scotland
- Age
- 69
- Posts
- 67
If you search the forum you might find some references to modifying the Triton 235 mm saw to take 250 mm blades. It is simple to do, works just fine and gives you another 7.5 mm depth of cut. It also greatly increases your choice of saw blade. I wouldn't recommend the modification if you take the saw out of the Workcentre to use hand-held though, because you need to remove the retractible blade guard.
cheers
George
-
19th March 2010, 01:03 PM #5newbie that's keen
- Join Date
- Mar 2007
- Location
- Bonny Hills, NSW
- Age
- 64
- Posts
- 517
thanks for suggestions / comments. They are always appreciated.
I did first turn it over to use in corss-cut mode but I was curring a tree branch. As this was not all the same level, I could not fit it between the table top and saw. Obviously when using a table saw this is not an issue as you just have to worry about the piece you are cutting being flat. Also, the idea of a sled seems easier (once I have made it) than using the cross-cut mode. I already adjusted my old one to fit on top of the table top.
I will search about using a 254mm saw blade - for one, I have some unused ones from my previous tablesaw!
I am still mostly in the 'playing' mode and trying to get the most out of what I have (as we all do).
thanks again
Mick
-
19th March 2010, 01:43 PM #6Novice
- Join Date
- Sep 2009
- Location
- Hobart, Tasmania
- Posts
- 23
Mick
Two issues that I can see:
1) In rip mode, the saw chassis locks into the table top which stops the saw sliding - without the table installed you will need to find another way to stop the saw moving (a clamp somewhere might work).
2) The saw chassis sits about 15mm above the sides of the workcentre (hopefully you can understand what I am saying!!) so any sled will need to be raised.
I am also not sure about using 3mm ply/mdf - the sled will not have any support underneath it and the weight of the wood being cut might bow the sled.
Sorry I didn't have any positive suggestions.
-
19th March 2010, 11:06 PM #7Intermediate Member
- Join Date
- Jun 2008
- Location
- United Kingdom
- Posts
- 49
I am not sure that cutting an irregular tree branch on the work centre in either position is all that wise.
Similar Threads
-
Dozuki - Depth of cut
By OsaTas in forum JAPANESE HAND TOOLSReplies: 10Last Post: 29th August 2009, 11:43 AM -
Plunge router - how to adjust the cutting depth?
By silverman in forum WOODWORK - GENERALReplies: 2Last Post: 18th January 2009, 06:41 AM -
Cutting Depth
By petersemple in forum SCROLLERS FORUMReplies: 6Last Post: 11th April 2008, 12:04 PM -
Dado depth
By Burf in forum WOODWORK - GENERALReplies: 5Last Post: 10th May 2003, 03:39 PM -
depth of cut
By thedilettante in forum TRITON / GMCReplies: 7Last Post: 12th January 2003, 09:50 AM