Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Dust Extraction Problems
-
17th April 2009, 03:27 PM #1New Member
- Join Date
- Nov 2008
- Location
- Melbourne
- Posts
- 5
Dust Extraction Problems
I've just gotten a triton router table and have the dust bucket set up to extract dust from the gaurd. the problem is the hose keeps blocking and then I completely lose suction throught the hose and the bucket just collapses in on itself. Then due to the lack of suction through the gaurd all the dust flies out the bottom and all over me.
Any suggestions?
-
17th April 2009 03:27 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
17th April 2009, 04:48 PM #2
Rollo,
Do you have a Triton Router ?
If so you need to connect a second hose to the router itself on the under side of the table. It's part of the clear acrylic shroud.
Ian
-
17th April 2009, 04:56 PM #3New Member
- Join Date
- Nov 2008
- Location
- Melbourne
- Posts
- 5
no I have a ryobi and the dust extraction port on it isn't a standard size so i'm struggling to attach anythng to it at the moment.
Do you think this will help with the other hose becoming blocked though? Or just help pick up additional dust that falls through?
-
17th April 2009, 06:01 PM #4
Rollo,
Dunno - but it's got to be worth a shot.
I use both extraction points on my Triton router/table and I've never had a cloggng problem.
I think it stands to reason that the more ways you remove the waste the less likely it is to collect any place.
Ian
-
17th April 2009, 09:08 PM #5Originally Posted by Rollo87
The extraction direction depends also on the type of cut you're taking. If you're profiling an edge, routing with the stock face down on the table, then the vast majority of waste will need to be extracted from below, with a lighter strength extraction from above - using the valves on the bucket. If you're performing a straight cut on an edge, then you are likely to be able to extract from either direction, although preferably from above, with a lighter strength below for gravity-borne waste.
Cutting housing joints (trenching/dado cutting) on the table has it's own difficulties. It's extremely difficult to extract from below after the initial part of the cut, as the waste will travel along the trench and shoot out at the left-hand side of the piece.
Ray
-
19th April 2009, 09:25 AM #6New Member
- Join Date
- Nov 2008
- Location
- Melbourne
- Posts
- 5
thanks ian, i'll give it a go.
Ray, I am getting some fairly large chips coming off, is this a problem with router speed or with the type of routing i'm doing. (planing 1mm off 50mm stock)?
-
19th April 2009, 10:31 AM #7Originally Posted by Rollo87
However, if I've not understood you correctly, let me know.
Ray.
-
19th April 2009, 03:53 PM #8New Member
- Join Date
- Nov 2008
- Location
- Melbourne
- Posts
- 5
thanks ray, i'll try upping the speed and see how that goes but if all else fails atleast I know I don't have a real problem just an issue with the type of routing i''m doing
Similar Threads
-
Dust Extraction
By amgsir in forum DUST EXTRACTIONReplies: 1Last Post: 17th July 2005, 02:26 PM -
PVC for Dust Extraction
By sandman in forum DUST EXTRACTIONReplies: 3Last Post: 20th February 2004, 01:51 PM -
Dust extraction
By Jackson in forum WOODTURNING - GENERALReplies: 14Last Post: 2nd February 2004, 10:22 AM -
Dust extraction
By Newatthis in forum TRITON / GMCReplies: 1Last Post: 9th September 2003, 10:11 AM -
Dust Extraction Problems
By kenmil in forum TRITON / GMCReplies: 22Last Post: 18th April 2003, 05:37 PM