Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
14th June 2009, 08:45 AM #1
MK3 Saw Chasis and saw upgrade advice.
Hi ,
I have a "newer" Mk3.I have had it since new but never found it to be that accurate.
I have a 250mm old Makita saw in it and the problem may be in the saw.
I now want to set it up to slot some Guitar fretboards and am thinking about getting a new Hitachi saw for it (instead of buying a table saw) but I find in crosscut mode it is always slightly out of whack and the saw seems to stick in the tracks .
I was thinking of getting the newer Saw slide Upgrade chasis and mount the new Hitachi saw in that.
Its got to be pretty accurate.
Am I waisting my time and money or would this improve the accuracy.
I can get a table saw for about (Carbatec) $900.00 or this will cost me about $400.00
Thanks guys for your input
Greg
-
14th June 2009 08:45 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
14th June 2009, 10:59 AM #2Senior Member
- Join Date
- Jun 2005
- Location
- Planet Earth
- Posts
- 477
Your problems can probably be solved with a spray of lubricant on the slide tracks or some ubeaut wax on the black sliders. A saw stabilizing bracket (or a homemade version) may solve the saw problem.
Spending on a decent table saw will always be a good long term investment.
-
14th June 2009, 11:14 AM #3
If you are talking about the height adjusting chassis, the this makes a huge difference to the MK3, and if you can get when I would go ahead with it.
However, to really get control of cross-cutting, I strongly urge you to make a crosscut sled. These are very simple to make, and will totally change you life with respect to the MK3. I haven't had my MK3 in crosscut mode, since I built the first sled 3 years ago. I now have a very high accuracy, and repeatability. Mind you, this is in combination with the height adjustment kit.
If you search the Triton form for 'sled', you'll get a lot of information.Chris
========================================
Life isn't always fair
....................but it's better than the alternative.
-
14th June 2009, 03:04 PM #4
Hi Greg
This view is heresy on this forum, so please, guys, do not crucify me.
My Triton 3 is now 25 years old and I still use the saw for bush carpentry and the router on the same table top for more accurate work. 25 years ago the Triton was affordable, table saws were an expensive dream. The economics has changed.
The basic problem, IMHO, is that the chassis plate for the saw flexes under the weight of the saws and it also wobbles a little in cross cut mode. This is a fundamental design problem that you learn to live with or byepass.
As Chris suggests, a crosscut sled is easy to make and very accurate.
And a table saw will be more accurate than a Triton.
Cheers
Graeme
-
15th June 2009, 10:16 AM #5
Thanks Guys for the replies.
I do have the Stabilizer bracket but I think the movement/play is in the gears on the saw shaft.
I have sprayed the tracks but they are always a bit tight.
I was thinking at one time of getting some bearings and trying to fit them to it.
The sled does sound like it may be the way to go though.
Regards
Greg
-
15th June 2009, 12:07 PM #6Senior Member
- Join Date
- Jun 2005
- Location
- Planet Earth
- Posts
- 477
-
19th June 2009, 06:27 PM #7
OK,
I picked up one of the 9 inch Triton saws (New) yesterday.I have decided to try it in the original mounting chasis and see how it goes.
I will go and set the whole thing up again from scratch and spend a bit of time "tuning" it.
I had a look around here regarding the the Sled and it seems pretty straight forward and by the looks of it its the way to go.
I hope I am not wasting my money and time but its a real bugger being on a tight budget!
Regards
Greg
-
23rd June 2009, 07:10 AM #8
bent chasis
I started to fit this new saw and setup the Triton again.When I was fitting the saw and setting it up (What a PITA that was) I noticed that the slide chasis is bent slightly in the centre near where the clamps are.
It almost looks like its been pushed down in the centre while in the table mode
I have made a couple of test cuts and it does seem to be cutting reasonably accurate but it still needs some adjustment
I was going to try to bend it back up but I dont want to break it as I would have no chance of getting another one these days.
Has anybody any suggestions or made or modified a chasis.I think they are cast Aluminium if I am not wrong and would snap like a carrot if I tried to bend it.
Thanks
Greg
Similar Threads
-
workcenter 2000 saw chasis
By sysiphus in forum TRITON / GMCReplies: 1Last Post: 17th January 2009, 07:30 PM -
To upgrade or not
By wajor in forum HAND TOOLS - POWEREDReplies: 35Last Post: 9th August 2007, 07:07 AM -
$44.00 LN #62 Upgrade
By MajorPanic in forum HAND TOOLS - POWEREDReplies: 6Last Post: 15th July 2006, 10:12 PM -
Upgrade
By Garry Szakacs in forum WOODIES JOKESReplies: 1Last Post: 8th July 2000, 01:45 PM