Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 24
Thread: Router table - how good is it??
-
20th February 2007, 01:09 PM #1
Router table - how good is it??
I am looking at purchasing a router table and wonder if the triton table and stand is up to doing precision work. I make guitars part time and use a triton 1400 router a lot during the process. It is the main tool used and I need very fine tolerances to get a top finish. I looked at the Carbatec unit with the tenon cutter and was impressed by the solidity of the table and fence.
I have briefly looked over a ex demo at bunnies that had oviously done a few days work and found it to be pretty rickety. I also wonder how much trouble it takes to get it set up so the table is rigid and dead flat.
Perhaps you guys can make comment on how you have found it. I have seen many threads that put it into the handyman category but not for finely detailed joinery.ray c
dunno what's more fun, buyin' the tools or usin' em'
-
20th February 2007 01:09 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
20th February 2007, 01:27 PM #2
If you get Australian Wood Review magazine, the new issue has 6 tables reviewed (by yours truly) including the two you mention.
I won't give away the findings as that isnt fair to the magazine, but I will say the Carbatec will be a better choice than the Triton for your needs. No table is perfect, but some are just better suited for particular tasks than others. Anyway grab the issue before you buy. It will probably answer most of your questions.How much wood could the woodchuck chuck if the woodchuck could chuck wood?
-
20th February 2007, 02:28 PM #3
Hello Mr Picker,
I have the Triton with a GMC router mounted in it and it's ok. Biggest problem is probably the depth "locking" device on the router - sometimes drops a bit.
Whilst not the best around, with a bit time and energy spent in the set up and double checking your distances etc you can end up with some good results. (good for me anyway!)
I also use the finger joiner system which once set up correctly has given me some good results too.
If you are handy at building such a thing there are some good plans for DIY tables around that may a: be cheaper, b: fit your needs better, c: give you more satisfaction (coz you DIY).
My 2c worth anyway.
Good luck!Cheers,
Matt Spl@tt
"Better off the World to Think you're a fool, than open your mouth and prove it!"
-
20th February 2007, 02:31 PM #4
I sold my Triton table, as did few others.
Too many spots where plates, rings and the rails all join up but none are flat. There's always a small ridge to upset the accuracy of the work.
Get a table top and phenolic plate from Grahame at Woodworksupplies and hook the Triton router under that. Much better.
http://www.woodworksupplies.com.au/category24_1.htm
-
20th February 2007, 03:27 PM #5SENIOR MEMBER
- Join Date
- Aug 2005
- Location
- Perth
- Posts
- 649
Agree with everybody above. great system well thought out but to many little knooks and crannys for stuff to catch on, if you get one the best thing you can do is make a smooth top for the whole unit, but then that defeats the purpose of buying one, get the idea
Steve
-
20th February 2007, 05:20 PM #6
-
20th February 2007, 06:21 PM #7Member
- Join Date
- Jun 2006
- Location
- Canberra
- Age
- 52
- Posts
- 90
G'Day Picker
I'm going to offer the alternate view here. A while ago I was chasing a router table. I wanted to build one myself but time and cost conspired against me. I ended up going down the Triton route and so far I'm very happy. Ive been routing curves on edges and grooves in long and short pieces. I've also done mortices, lap joints and edge jointing on the table. The Triton has done every job well. It comes with a pretty reasonable fence and for not a lot of money gets you going with a router table.
I've yet to find the limitations of my table but I'm sure that time will come. When it does I'll be giving Grahame at PWWS a call and upgrading the top. In the mean time I'm enjoying some great features like the biscuit joiner and (soon to be purchased) finger joiner.
When I look at some of the better systems out there I see how they would be more accurate but I've yet to do a job where the accuracy of the Triton wasn't up to the task.
Hope that helps
regards
Manix
-
20th February 2007, 08:27 PM #8
Hi Manix
Outside of fine woodwork the triton is great. But if the finer side is your thing then I recommend against it. I am not sold on the bells and whistles of upmarket machines.
IMO the most important factor in routing is a dead flat surface and sadly our orange brother struggles here.
But I love that triton router in the table mode.
cheers
dazzler
-
20th February 2007, 08:39 PM #9
I had a serious whinge, about my RTA 300, on the forum last year. I said then, that it wasn't fit for purpose out of the box. The differing heights, all but made it impossible to use properly.
I then proceeded to spend a fair bit of time, hand working the red plastic mounting plate 'levellers', down to the 'correct' height. It wasn't perfect, but was a vast improvement.
Since then, I have thrown them away completely, and drilled the steel bars out to accept hex head screws, with a nut on each side of the bar. Adjusted the height of the hex heads, until the mounting plate was perfectly level, and then ran some CA down the threads. Problem solved, and it turned out to be an easy solution.
I am now very happy with it, and the fence is a dream. I don't do a lot of routing, at this stage, and it suits my needs. Should my needs change, then I will look to making my own table, with a router raiser in it.Chris
========================================
Life isn't always fair
....................but it's better than the alternative.
-
21st February 2007, 08:00 PM #10SENIOR MEMBER
- Join Date
- Apr 2006
- Location
- Broken Hill
- Posts
- 540
Hi Chrisb691
Have you got any pics to illustrate what uou did - and what it looks like now?
Please?
Jedo
-
21st February 2007, 08:47 PM #11
-
22nd February 2007, 11:04 AM #12"Looking west with the land behind me as the sun tracks down to the sea, I have my bearings" Tim Winton
-
22nd February 2007, 07:05 PM #13
No it isn't incorporated in the TS. I'd only just bought that top and it was just sitting on the extension arms of the TS. That's why it moved a couple of times when I was using it.
The top now sits on a Triton Router table stand. I still haven't screwed it down but it woks OK.
-
22nd February 2007, 08:51 PM #14Member
- Join Date
- Jun 2006
- Location
- Canberra
- Age
- 52
- Posts
- 90
Dazzler, Picker
Yep, I'll have to admit that the table isn't perfectly flat and after reading Picker's requirements it may not be for him.
Over the last few weeks I've routered some stuff to what I'd say are pretty fine tolerances but I can certainly appreciate how a perfectly flat (and larger) table would help.
As for "fine" woodworking, I thought all the stuff I did was fine. When I say to SWMBO "I'm off to the shed" she always say "fine". What better endorsement can I get?
regards
Manix
-
22nd February 2007, 08:53 PM #15
How about the triton stand with the engineered table top with the LE Fence
from PWWS???
Is the table stable ??
I saw a demo for sale at bunnies [only $40 of rrp and it looked pretty sad] that was doddery are they all like that??
graham from PWWS has a triton table version....If I can get a decent table to put the top and fence on i'm good to go
oh an i dont feel like building a table that is dead dead flat on top to put the engineered table top onto i just wanna get on and make some more geetars.ray c
dunno what's more fun, buyin' the tools or usin' em'
Similar Threads
-
Challenge to Create the Ideal Router Table
By rodm in forum ROUTING FORUMReplies: 215Last Post: 26th July 2021, 08:34 PM -
Need advice about GMC router and table.
By strangerep in forum ROUTING FORUMReplies: 36Last Post: 20th April 2007, 09:23 PM -
Review: Veritas Router Base Plate from Lee Valley
By silentC in forum ROUTING FORUMReplies: 15Last Post: 20th August 2004, 09:17 AM -
World's Cheapes Router Insert
By bitingmidge in forum ROUTING FORUMReplies: 10Last Post: 8th June 2004, 08:26 AM