Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 4 of 4
  1. 2nd July 2020, 12:09 AM #1
    Donga
    Donga is offline New Member
    Join Date
    Mar 2018
    Location
    Albany
    Age
    40
    Posts
    9

    Default WC2000 blade not 90deg

    Hey guys!

    I have aquired a few bit of gear over the last couple of years. A Workcentre2000 with C9 saw, extension slide table, router table top with router, original castors. (All up less than $400) All in pretty decent nick

    Havent mucked aroubd with it too much but when I did i couldnt get the blade straight up and down vertical. The saw cant adjust that way. It has the older style chassis and I see it looks like it sags a bit.

    Is there any ways to remedy this? Ideally I would like to get the new chassis with a height adjuster winder but failing that can i beef up the chassis?

    Thanks for your help in advance
    Reply With Quote Reply With Quote
  2. 2nd July 2020 12:09 AM # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Age
    2010
    Posts
    Many





     
  3. 5th July 2020, 07:10 PM #2
    Bauldy
    Bauldy is offline SENIOR MEMBER
    Join Date
    Feb 2012
    Location
    Rosslyn Park, Adelaide
    Posts
    182

    Default

    I used a couple of shims to adjust mine.

    I found it rigid enough for my use, so did not do anything else.

    Regards

    Bauldy
    Reply With Quote Reply With Quote
  4. 6th July 2020, 11:12 PM #3
    Chrism3
    Chrism3 is offline GOLD MEMBER
    Join Date
    Nov 2009
    Location
    Canberra
    Posts
    1,301

    Default

    You can get the new chassis and the height winder, but only if you are prepared to sacrifice an arm and a leg, and then you wouldn't be able to operate it!
    Reply With Quote Reply With Quote
  5. 6th July 2020, 11:16 PM #4
    Donga
    Donga is offline New Member
    Join Date
    Mar 2018
    Location
    Albany
    Age
    40
    Posts
    9

    Default

    Thanks for the replies guys. I have seen the stabilising bracket, might look into something like that.

    I have shimmed mine up but i dont trust it long term. Perhaps i need a better shim.

    Those accessories aint cheap!
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Line Shaft 90Deg Belt Turn
    By DSEL74 in forum METALWORK FORUM
    Replies: 10
    Last Post: 26th August 2015, 01:27 PM
  2. Cutting a 90deg into sheet
    By vicente in forum WOODWORK - GENERAL
    Replies: 7
    Last Post: 21st April 2012, 12:14 PM
  3. WC2000 blade hitting infill strip.
    By Ozkaban in forum TRITON / GMC
    Replies: 2
    Last Post: 9th December 2008, 02:52 PM
  4. .Saw blade guard on WC2000
    By pommyphil in forum TRITON / GMC
    Replies: 10
    Last Post: 26th October 2008, 04:18 PM
  5. WC2000 top for Mk3
    By scubabob in forum TRITON / GMC
    Replies: 1
    Last Post: 18th September 2006, 01:27 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules