Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
-
20th February 2014, 05:20 PM #1Intermediate Member
- Join Date
- Jan 2014
- Location
- NSW
- Posts
- 32
What's the size of the Trition biscuit slot cutter?
I couldn't find any information on this other than an old thread here https://www.woodworkforums.com/f15/triton-biscuit-joiner-cutter-disc-132421.
I'm actually in the same position and was hoping to get a replacement cutter to fit in the joiner table (it's the old pivoting system) until the cheap biscuit joiners are available again at Aldi . I was about to get the Manz on sale at carbatec until I read about what other forumers had to say about it.
So if anyone can measure the size of their triton cutter I would be most appreciative. A poster in that thread indicated that the carbatec 50.8 x 4mm cutter would work but the original poster didn't confirm this - I guess an absent response means it probably did! I'd get the original cutter from toolsparesonline in the UK if their postage costs weren't so astronomical.
-
20th February 2014 05:20 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
20th February 2014, 06:07 PM #2SENIOR MEMBER
- Join Date
- Jul 2009
- Location
- inverloch
- Posts
- 472
Hi Rocketwiz, My Triton biscuit cutter is 48mm by 3.8 thick.
Cheers,
Safari
-
20th February 2014, 07:17 PM #3GOLD MEMBER
- Join Date
- Aug 2005
- Location
- Queensland
- Posts
- 2,947
Before I bought my Makita biscuit machine I used a 4mm cutter in my router. It worked fine and had no problems.
Bear in mind that "real biscuits" are designed to swell with the glue and will fill the 4mm slot perfectly. As "real biscuits" as opposed to bits of wood cut in a biscuit size are actually compressed and designed to swell - for this reason they should be kept in an airtight container as they will absorb moisture from the air and swell enough to cause problems when inserted in a correct sized slot. I have heard of people putting them into a microwave oven to drive out any moisture but have never done it and can't see how an expanded biscuit would come back in size - I could be wrong but others who have tried it may chime in.
See post #5 and #16 in the link.
https://www.woodworkforums.com/f11/router-bits-suit-biscuits-129146
-
20th February 2014, 08:20 PM #4GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,271
I just went into my garage and measured a couple of my Triton slot cutters.
They are 47.8mm dia by 4mm thick and the bore hole size is 8mm, could be a bit of wear and tear to reduce the size a tad on my ones, as they have been worked.
A quick check of the Carba-Tech catalogue on my desk alongside the computer tells me that they have slot cutter blades without arbour that are virtually identical for $22.00. Correction, $25.00 old catalogue.
Part number 822-340-11 47.6mm dia by 4mm thick and a bore size of 8mm.
http://www.carbatec.com.au/822-slot-...-blades_c17750
Could this do the job?
Mick.
-
21st February 2014, 01:06 AM #5Intermediate Member
- Join Date
- Jan 2014
- Location
- NSW
- Posts
- 32
Thanks guys. The cutter and arbor is almost half the price of a cheapy biscuit joiner! If the Aldi one doesn't come about soon I might have to spring for it.
-
21st February 2014, 08:18 PM #6GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,271
Umm, unles I'm thinking wrongly, you would only require the slot cutter. It will bolt directly onto your existing arbour from the Triton unit.
Mick.
Similar Threads
-
Router Bit - T Slot Cutter - where to buy
By Arry in forum ROUTING FORUMReplies: 3Last Post: 20th January 2014, 01:59 PM -
Supplier of Slot Cutter
By Carry Pine in forum BOX MAKINGReplies: 6Last Post: 3rd August 2010, 10:45 PM -
Slot Cutter/Router as a Biscuit Joiner
By sCORCH in forum ROUTING FORUMReplies: 4Last Post: 8th November 2007, 06:06 PM -
Small tee slot cutter
By neksmerj in forum METALWORK FORUMReplies: 4Last Post: 2nd July 2007, 01:16 AM -
biscuit slot
By offcut in forum TRITON / GMCReplies: 9Last Post: 8th August 2004, 01:48 AM