Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 24
-
6th September 2012, 01:55 PM #1
Derek: You wuz right and I wuz wr...wrrr...
ong. BUT I was more wrong than you were right!
We had a discussion some months ago about the wisdom of using non-slip rubber mats in tool drawers to prevent them slipping around, and you were saying that it may well promote rust.
Indeed I had had no problems until I glued the mats down with some old Aquadhere. What transpired next beggars belief that I could do such a crazy thing! Before the glue was more than a minute dry I put the tools back in place. They were rusty the next day fer cryin' out loud!
I mean, just exactly how dumb was that???
I have since given the rubber a bit of a run over with Camellia oil, and all seems to be good, but it's been pretty dry up here for the last few months. I don't want to take the rubber out because it does its primary function really well, but nor do I want to take any chances with a couple of saws I purchased recently from IanW (and they are crackers!). I have introduced some Silica Gel sachets scattered around the drawers, and lifted the saws up onto timber blocks.
Yup, keeping a very vigilant eye out!
Cheers
Brett
-
6th September 2012 01:55 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
6th September 2012, 02:07 PM #2
Bret I knew not of other post but I have found that anti-slip stuff damn annoying it will stick to anything after a while. No idea why
I was being given pro movie gear a while back it had been stored in its cases and in a bedroom cupboard all the special foam had adhered to the cameras, lens, and leaked into the cracks. It was all useless to costly to clean.
-
6th September 2012, 02:12 PM #3
Cockroaches also like to eat it.
Cliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
6th September 2012, 02:50 PM #4
Ray, it's prolly just good old perishing after a few years. This type of rubber seems to have a good life - I've had it on the dashboard of cars for some time in full sun, and didn't go sticky.
Cliff, the main roaches up here are natives, and are timber eaters. Just a little slower, and they don't fly AT you. Cats still like 'em though, and they still make that very satisfying "crack" under a shoe.
-
6th September 2012, 03:44 PM #5
I'd say it was mainly the acidic fumes from the pva that caused the overnight rust. Steel hates that.
-
6th September 2012, 03:51 PM #6
You may well be right there Mick. The glue was many years old, and had turned to a snot consistency, with a smell like silicon sealer - not unlike vinegar. Very odd.
-
6th September 2012, 06:09 PM #7Jim
- Join Date
- Feb 2008
- Location
- Victoria
- Posts
- 3,191
-
6th September 2012, 06:59 PM #8
Indeed not Jim, but i think it was too fast and aggressive for that.
-
6th September 2012, 09:12 PM #9Jim
- Join Date
- Feb 2008
- Location
- Victoria
- Posts
- 3,191
-
7th September 2012, 12:25 AM #10
Sorry about that Brett
What you need to do is remove the rubber mats, then fill your drawers with saw dust, and plonk the tools on top of that.
Hang a pyramid over the top, and they'll stay sharp as well.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
7th September 2012, 08:42 AM #11Jim
- Join Date
- Feb 2008
- Location
- Victoria
- Posts
- 3,191
-
7th September 2012, 09:27 AM #12
-
7th September 2012, 10:46 AM #13
Hi Alex
Years ago, when I was restoring an old car, there were many stories of those who would fill the longitudinals with foam in the belief that they could prevent moisture getting in. These were the cars that rusted fastest. Moisture would be trapped by the foam, held against the steel, where if courseitbwould lead to rust.
By far the best method of avoiding rust is an atmosphere where the temperature does not vary, and where moisture vapour cannot be created. Add a protective layer to the steel as well.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
7th September 2012, 12:34 PM #14Jim
- Join Date
- Feb 2008
- Location
- Victoria
- Posts
- 3,191
Derek, as a ps. The new agers never seemed to extend the powers of pyramids to woodworking tools did they. Too easily disproved I suppose. Imagine the market out there for pyramid shaped tool chests.
Cheers,
Jim
-
7th September 2012, 12:38 PM #15
Similar Threads
-
Derek did you get to trial one of these?
By ian in forum HAND TOOLS - UNPOWEREDReplies: 14Last Post: 6th April 2009, 11:24 AM -
This is not really working — or Derek, please help
By ian in forum HAND TOOLS - UNPOWEREDReplies: 12Last Post: 31st December 2008, 08:20 AM -
Derek?
By Grunt in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 14Last Post: 17th May 2005, 03:53 AM -
Thank You Derek!
By DPB in forum WOODWORK PICSReplies: 30Last Post: 17th February 2005, 08:49 AM -
Just for Derek
By outback in forum HAND TOOLS - UNPOWEREDReplies: 6Last Post: 12th March 2004, 06:52 PM