Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
Thread: Ploughing - Stanley 13-052
-
20th December 2010, 09:41 PM #1
Ploughing - Stanley 13-052
So, the Stanley 13-052 is a plastic handled plough plane, comes with metric (4, 6, 9, 12mm) and imperial (1/8, 3/16, 1/4, 5/16, 3/8, 1/3") blades.
Its not bad... not great... a bit rough in the finish and the blade depth adjuster could do with a lock nut as the blade will retract during use (well, maybe not if you are not a heavy handed monkey like me ). Absolutely needs a knicker/scribing blade.
Aside from these 'sins', its a goer.
Today I needed to rip out some edge strips from some boards, so instead of using a saw, the 13-052 got taken out.
A quick freehand rub on my final stone to make sure the blade is ready, set the width of the rip with the marking guage, scribe a line on the timber stock, clamp down... set the stopwatch ... 17.30 minutes later I've ripped out a 2300 x 27 x 30mm board and then jointed it with a handplane a smidge past the scribe line. 27mm is the depth of the plough cut.
Basically its scribe a line where you want the finished edge to be, set the fence on the plane to be a smidgin over that, clamp the board.
Plough, (keep the plane vertical, don't lay it over!) when the plough cut is deep enough, swap the board over and re-clamp, keep plouging, when the plough cut breaks through in places I use a gentler hand till the board breaks down the waste line.
Reclamp with the ploughed edge up and use a bench plane to take off any final waste and to joint that edge.
With a knicker/scribing blade I'd minimise the few swipes with the bench plane to take it to a good edge ready jointed state.
Cheaper than a Stanley 45 or 50... underrated because of the modern plastic handle. Works just fine... even with the 1mm+ shavings I've been taking.
Yeah I know, 17.30 mins is slow compared to a circular saw/table saw/bandsaw... but its hardwood (teak), faster and more accurate than a handsaw, less carbon credits, and thats the way we roll at my place!
Seeya!
Sorry, big pic's cause I forgot to change the camera settings.Last edited by Clinton1; 20th December 2010 at 09:43 PM. Reason: spelling
-
20th December 2010 09:41 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
14th June 2011, 11:55 PM #2SENIOR MEMBER
- Join Date
- Nov 2007
- Location
- Victoria
- Posts
- 734
Clinton, I just tried this and it worked a treat ! Thanks for posting the method
Ripped a 900 long x 19mm thick bit of Vic Ash/Tas Oak in half with my Record 044 in about 10 minutes. Sounds slow but it was good fun. Next time with a bit more practice I reckon I could halve that time.
Did you buy your Stanley new ?
-
17th June 2011, 10:34 AM #3SENIOR MEMBER
- Join Date
- Nov 2007
- Location
- Victoria
- Posts
- 734
New world record.....4 minutes at 10pm last night !!!!!!
-
18th June 2011, 10:29 AM #4
Hi Clinton
this mini report on a Stanley 13-050 (with spurs!), and the parts list, may be of interest.
https://www.woodworkforums.com/f152/s...-plane-128931/
And, I just love my Record 044s for ploughing.
cheerio, mike
Similar Threads
-
Son of Stanley #52
By derekcohen in forum HAND TOOLS - UNPOWEREDReplies: 26Last Post: 15th March 2010, 02:12 AM -
Stanley #8 and Stanley #62 LA Plane
By Shedhand in forum HAND TOOLS - UNPOWEREDReplies: 5Last Post: 19th April 2006, 03:04 AM -
Quick ! Quick, ya Stanley collecting freaks..a stanley # 1 !
By JDarvall in forum HAND TOOLS - POWEREDReplies: 29Last Post: 17th March 2006, 09:17 PM