Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 12 of 12
-
21st October 2015, 09:59 AM #1SENIOR MEMBER
- Join Date
- Dec 2005
- Location
- Sydney
- Age
- 79
- Posts
- 647
Saw restoration to the nth degree
No compromises here...
https://www.youtube.com/watch?v=KxWd4bh2zk4
saw even cuts
-
21st October 2015 09:59 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
21st October 2015, 04:46 PM #2
He got a nice shine on things but may have missed the point a bit as to restoration. A bit agressive in his methods. Be surprised if there is any detail left on that medallion after the wire wheel.
Regards
John
-
21st October 2015, 07:37 PM #3
-
21st October 2015, 08:27 PM #4Member
- Join Date
- Apr 2009
- Location
- Wollongong
- Posts
- 88
AWFULLY shiny. Filling and re-drilling the holes in the plate seemed a bit excessive, but perhaps the plate was not original. Whether it was or not it looked like he was not the first to take that saw apart and clean it.
-
22nd October 2015, 12:32 PM #5SENIOR MEMBER
- Join Date
- Dec 2005
- Location
- Sydney
- Age
- 79
- Posts
- 647
Here is another one - with a new take on plate thickness - https://www.youtube.com/watch?v=zxjIxa_l2x0 - now to get back to my tax return...
-
23rd October 2015, 10:40 AM #6
A lot better than the last guy.
Regards
John
-
23rd October 2015, 11:10 PM #7
I don't mind the first guy's job. I think he did ok, given the piece.
Seems more functional than the second guy's. (But I like that guy for other videos)
I thought it was interesting that they both (seemed at least) to have little issue drilling through the sawplates.
My few experiences with handsaws have been very different (before the carbide bits).
Cheers,
Paul
-
25th October 2015, 03:20 PM #8
I skipped through quite a bit of both videos, Paul, but did watch one hole being drilled. I couldn't tell if he was using an ordinary HSS drill or not, but to judge by the smoke & the scorch mark on the wooden backing board when he removed the saw, it involved a lot of pressure & heat. That works, though you end up with a very dull HSS bit after a couple of holes. An alternative is to chuck a squared-off nail in your DP and hold it at high speed against the plate in the spot where you want to drill. Use moderate pressure & hold it there 'til there is a red-hot spot, then let it cool, and it should be soft enough for you to easily drill it with a regular HSS drill. However, a carbide bit makes the job much quicker & easier, & no smoke.....
Cheers,IW
-
25th October 2015, 04:13 PM #9Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
However, a carbide bit makes the job much quicker & easier, & no smoke.....
-
26th October 2015, 05:14 AM #10
Speaking of red-hot and smoke ... I wasn't going to link this 'cos the guy is a little bit irritating to listen to (but then again ... look who's talkin')
but ... in the spirit of cowboy experimenters everywhere ...
(I've seen him in the past and dismissed him until I noticed the number of subscribers and number of views on whatever video it was)
-
26th October 2015, 05:16 AM #11
On a whole other level ...
-
26th October 2015, 05:39 AM #12
Same guy has rather more luck with files than the other one
Similar Threads
-
How can I cut a 68 degree angle?
By garfield in forum WOODWORK - GENERALReplies: 8Last Post: 16th May 2013, 11:44 AM -
82 and 90 degree countersinks
By jack620 in forum METALWORK FORUMReplies: 4Last Post: 19th November 2012, 09:08 PM -
25 degree bevel??
By mattym83 in forum WOODWORK - GENERALReplies: 4Last Post: 11th October 2009, 04:49 PM -
campbell hausfeld 34 degree framing nailer and 30 degree nails
By oggie in forum HAND TOOLS - POWEREDReplies: 0Last Post: 14th September 2009, 11:51 AM