Needs Pictures: 0
Picture(s) thanks: 0
Results 31 to 35 of 35
-
23rd September 2021, 01:07 PM #31GOLD MEMBER
- Join Date
- May 2009
- Location
- melb
- Posts
- 1,125
Has anyone tried the Luban gauge?
-
23rd September 2021 01:07 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
25th September 2021, 09:01 AM #32Senior Member
- Join Date
- Apr 2017
- Location
- Éire
- Age
- 39
- Posts
- 297
I have the newer Veritas marking gauge, bought for the offset function, rather than the micro adjust.
It has a bit of play, should you decide to use that adjustment function.
I lock it down, but gets loose again, and I don't want to crank on it as the hollow stem has very thin walls.
The adjustment is easy/precise should you forget about that " micro adjust feature"
It is a nice fit, the only problem I have, or one might have if using it like Cosman's is the single lock screw.
It'll move if you are a bit heavy handed, (I don't have a router plane yet)
I can depend on the badly made Titemark knockoff, which has another pointless (as far as I can make out)
micro adjust also, but the stem is a bit awful.
Even so with that fit, it stays locked having both screws.
(if someone is making them still, then note that the cutter doesn't sit flush, as screw is in the way,
so cannot be dropped onto the work... and 5 quid spare Veritas cutter's don't fit.)
Tom
-
25th September 2021, 11:06 AM #33
I do not recommend any of the knock-off gauges. They are a crap shoot for finish, plus replacement cutters are unpredictable. Spend a little more once and get a reliable Tite-Mark or Veritas, or make your own with their parts. Veritas sell the stem/cutter separately for their new adjustable gauge.
I was one of the early testers for the micro adjustable Veritas, and now also purchased the kit to add to a wheel gauge I built a few years back ….
The TM micro adjust is better, but also more spendy.
Frankly, I am very happy with non-fine adjustable gauges, and the cheapest Veritas is an excellent gauge.
On the left is the Veritas Anniversary gauge in SS. These are now only available in brass. One of my favourites. On the right is the cheapest Veritas, and set up here with a Tite-Mark slicing blade …
Just get the cheaper Veritas with the standard blade, and you are good to go.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
30th October 2021, 08:20 PM #34
Update on Igaging cutting gauge wheels
Ok; thanks to Derek’s suggestion I can now confirm that Veritas cutting wheels fit the Igaging gauges, including the digital one. They are also sharp enough to allow the gauge to act as a sort of router; this is American White Oak:
71E89173-9972-4611-97DC-DF2694616C0C.jpeg 3F640251-675E-477D-B03C-0A74546A63F7.jpeg
One issue though; the Veritas wheel wasn’t actually flat and needed to be lapped on a diamond stone which took off a fraction of a mm. You get less than 0.2 of a mm to hone away before the screw head becomes flush with the wheel.
3FFFD637-D7B0-4675-A604-A27872390FB8.jpeg
Lastly, the Aus distributer is now selling Igaging wheels on his Ebay store; $13 inc shipping. However; if you live near a Carbatec store the Veritas ones are only $10 and my local toolshop ordered me one in for $13…Nothing succeeds like a budgie without a beak.
-
30th October 2021, 08:25 PM #35One issue though; the Veritas wheel wasn’t actually flat and needed to be lapped on a diamond stone which took off a fraction of a mm. You get less than 0.2 of a mm to hone away before the screw head becomes flush with the wheel.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
Similar Threads
-
This IS a marking gauge.....
By IanW in forum HAND TOOLS - UNPOWEREDReplies: 13Last Post: 2nd April 2017, 07:11 PM -
Marking Gauge Vs Cutting Gauge
By GraemeCook in forum HAND TOOLS - UNPOWEREDReplies: 10Last Post: 11th July 2014, 01:10 AM -
Cutting Gauge or Marking Gauge ???
By GraemeCook in forum HAND TOOLS - UNPOWEREDReplies: 34Last Post: 4th July 2013, 09:07 AM -
Which marking gauge?
By SimonArchibald in forum HAND TOOLS - UNPOWEREDReplies: 27Last Post: 30th June 2013, 08:30 PM -
Marking Gauge
By RedShirtGuy in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 6Last Post: 28th July 2012, 09:48 PM