Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Stanley #45 Combination Plane
-
14th December 2011, 08:22 AM #1
Stanley #45 Combination Plane
I have just acquired a #45 plane which I am bringing back to life, it has now been cleaned, the rosewood handles shellacked, and waxed, and the missing pin on the blade adjuster replaced, with one I made from a section of an old 5/32" drill bit.
I am now starting on cleaning, sharpening, and honing the blades which seem to have a range of bevel angles. Before I make my own decision on what I set these angles to, can anyone provide informations as to what the factory angle is ? or the most commonly used angle is ?
regards
-
14th December 2011 08:22 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th December 2011, 09:26 AM #2
Not answering your question - but I saw this and thought it was neat enough to reference again :
http://www.tooltrip.com/tooltrip9/st...anes/45man.pdf
from
https://www.woodworkforums.com/f152/s...estion-136504/
although ...
Derek says
"Setting up for the Stanley #46 Combination Plane
The Stanley #46 Combination plane: blades have a 20 degree skew angle and the bevels are 25 degrees."
at
The Veritas (LV) Skew Angle Jig
I don't know if you can take anything from that for the #45?
Paul McGee
-
15th December 2011, 01:28 PM #3
A single angle of 35 degrees - according to UKalf www.cornishworkshop.co.uk/combihow2.html
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
15th December 2011, 01:40 PM #4.... some old things are lovely
Warm still with the life of forgotten men who made them ........................D.H. Lawrence
https://thevillagewoodworker.blogspot.com/
-
15th December 2011, 04:45 PM #5
Thanks Paul, Vann & SG
35 degrees it is. I have done one blade to try it out and it works fine. Now all I have to do is sharpen the other 22 blades and get the Operator trained. so I may make a box to store the plane and get some use out of the plane.
I am going to be busy for the next few weeks but I will try to post some photos later.
Regards
-
20th January 2012, 11:52 AM #6
G'day all
I eventually sharpened all 22 blades for the #45, lapped the backs set the bevels @ 35 degrees and honed the profiles with slipstones.
For step one of the " Operator Training " I decided to make a storage box for the plane using some recycled 90 x 16 mm WRC boards, which were edge jointed & glued to get the width of board needed. Grooves were ploughed using a 1/4 " cutter in the 45 for the top & bottom panels made up from WRC. and the panels fielded with a rebate on the 45.
Joints were simple glued mitres reinforced with Bamboo trenails.
I can't say that I enjoy working with WRC as it's properties are too close to sponge rubber for me. However, a big advantage was the nice straight grain, which helps in using a 45.
Regards
-
20th January 2012, 12:52 PM #7
Very nice B. I'm looking our for a 45 myself ATM.
Regards,
Denim
-
20th January 2012, 08:32 PM #8
The box and the #45 look great. I have a #46 that needs a box just like that and I have a Sargent version of the #45 the 1080. It is in it's original box but the box is a bit sad. Needs a rebuild or a new improved version. Added to the list.
Those were the droids I was looking for.
https://autoblastgates.com.au
Similar Threads
-
Stanley 45 and combination planes
By Tiger in forum HAND TOOLS - UNPOWEREDReplies: 15Last Post: 27th June 2011, 07:33 PM -
Stanley 13-050 Small Combination Plane
By mike48 in forum HAND TOOLS - UNPOWEREDReplies: 3Last Post: 27th December 2010, 06:05 PM -
Stanley combination square
By graemet in forum HAND TOOLS - UNPOWEREDReplies: 2Last Post: 12th May 2005, 12:20 PM