Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 76 to 90 of 943
-
8th May 2010, 06:30 PM #76
Thumbsucker my order is correct.
Thanks for all the hard work
Jerryj
-
8th May 2010 06:30 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
8th May 2010, 06:41 PM #77Member
- Join Date
- Mar 2009
- Location
- Geelong
- Posts
- 50
Hi TS, i PM'd you a while ago and thought i confirmed that i was after a 2-3/8 blade bevelled and with matching cap iron for my #7. I dont think i am on the list at this stage though?? Please add me to the list if possible
Thanks
Ashley
-
8th May 2010, 06:44 PM #78
I have added you to the list Ashley.
-
18th May 2010, 11:02 AM #79
Hey TS,
Am I too late to add to the order? If I am, then that's cool but if I'm not too late can you please put me down for the following?
1 x 2 3/8" blade (with bevel) + cap iron
1 x 2" blade (with bevel) + cap iron.
Thanks very much.
Denim.
-
18th May 2010, 05:35 PM #80
DENIM I have added you to the list. About 90 Stanley blades still up for grabs.
-
18th May 2010, 06:52 PM #81
Thanks very much TS and sorry for any inconvenience I may have caused.
Denim.
-
21st May 2010, 12:40 AM #82Senior Member
- Join Date
- Apr 2008
- Location
- Crows Nest, NSW
- Posts
- 111
Hi Helmut,
If I'm not too late I'd like to jump aboard this order.
I picked up two blades in the 1st round and they are just fantastic.
Please put me down for:
1 x 2" blade bevelled with cap iron
1 x 1 3/4" blade bevelled with cap iron.
1 x 60 1/2 block plane blade - if its the new style 3 slots 1 3/8".
Thanks,
Geoff
-
21st May 2010, 10:27 AM #83
Hi Geoff - I have added you to the list.
-
21st May 2010, 12:25 PM #84
G'Day
I like the sound of this. Would it be possible to put me down for:
2 x 2 3/8 blades with bevel, screw and cap iron
1 x 60 1/2 block plane blade (I'm assuminging of the older style as the current blade is 1 5/8 wide and has 11 grooves milled in it)?
I may need to add to this once I work out what's going on in my shed.
Many thanks
-
21st May 2010, 02:45 PM #85
Horaldic I have added you to the list.
Regarding the block plane blade, would you be so kind to measure up your blade and post it back in the thread.
If anyone else has a #60 1/2 blade, could you do the same. We have never made one of these and we need a template for the blade.
-
21st May 2010, 11:42 PM #86
G'Day TS
I believe my block plane is of 1930's vintage. If I had the correct applications I'd provide a diagram, however, a description will have to do. These dimensions are measured using my Mitutoyo dial caliper
Overall length 4 1/2"
Width 1 5/8"
Thickness 0.07" (uniform 2mm)
A slot of length 1.35" and width 0.445" with radiused ends cut through the blade.
This begins 1.82" from the top.
There are 11 machined cuts into back of blade (obviously cut with a circular cutter),
Cuts extend at their deepest point to half the depth of the blade.
Cuts begin 1/2" from the top of the blade and the last cut is actually split in half by the beginnings of the through slot on the blade.
Length of cuts is on average 1/2"
Width of cuts is 0.08"
Gap between cuts 0.05".
I hope that describes the blade sufficiently? If there are further measurements needed I'm more than happy to provide them.
Many thanks
Horaldic
-
25th May 2010, 12:50 AM #87Eschew obfuscation
- Join Date
- Mar 2010
- Location
- Berowra, Sydney
- Posts
- 171
Hi TS,
If the order is still open I'd like a 2" blade bevelled with cap iron, suitable for an English Stanley #4.
Let me know if that's not enough info - I'm still rediscovering the world of hand tools.
Thanks,
Brett.
-
25th May 2010, 07:50 AM #88
Brett I have added you to the list.
-
25th May 2010, 09:48 PM #89Senior Member
- Join Date
- Jun 2007
- Location
- Queanbeyan NSW
- Posts
- 231
plane blades
Have had a think about a few blades ive tried and compared your 2 5/8 in my record
could you please add a 1 3/4, a 2, a 2 1/4 and a 2 3/8 to the order
all wuth bevel and chip breaker
Cheers Neil
-
25th May 2010, 11:27 PM #90Novice
- Join Date
- Feb 2006
- Location
- Melbourne
- Posts
- 24
Hi TS,
Could you please put me down for 1 x 2 3/8" (Stanley/Record size), bevelled with cap iron.
Many thanks,
Liam
Similar Threads
-
Stanley Bench Planes Replacement Blade Bulk Order
By thumbsucker in forum HAND TOOLS - UNPOWEREDReplies: 1385Last Post: 21st September 2009, 08:30 PM -
How to install an old wooden plane blade into a stanley.
By JDarvall in forum HAND TOOLS - UNPOWEREDReplies: 17Last Post: 2nd September 2006, 06:46 PM