Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Waxing a table saw help
-
3rd February 2016, 02:50 PM #1Novice
- Join Date
- Aug 2012
- Location
- Narre Warren South Vic
- Posts
- 19
Waxing a table saw help
Good day and I hope that I have entered the correct forum for my question. Can someone please tell what type of wax I should use to rub on my table saw top to assist in the easier movement of the timber. This question would also apply to my bandsaw. I went to Bunnings and they tries to sell me furniture polish wax which specifically said on the information panel - for polishing and buffing old and new timber furniture. Any information would be appreciated and also if it is a specialty product; where would I buy it. For information, my table saw is a Dewalt 7491 which I think is aluminum as it scratched easily when a piece of wood had an unseen nail sticking out.
-
3rd February 2016 02:50 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
3rd February 2016, 03:05 PM #2GOLD MEMBER
- Join Date
- Jun 2003
- Location
- Sunbury, Vic
- Age
- 84
- Posts
- 2,719
Our Boss's U-beaut Traditional Wax or candle wax. I scrub it in with a scouring pad and polish off. Do NOT use anything with silicone in it as it affects any finish you want to use on the timber.
Trad wax should be available at Carbatech in Springvale.Tom
"It's good enough" is low aim
-
3rd February 2016, 03:37 PM #3Novice
- Join Date
- Aug 2012
- Location
- Narre Warren South Vic
- Posts
- 19
Thank you for the quick reply Chesand. I often visit Carbetec to buy one thing and end up with more (just in case I may need it problem). I hadn't seen any wax products there before so I'll head over this week and look more closely.
-
3rd February 2016, 03:43 PM #4GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,330
I was going to recommend Silverglide, which I use, but I just saw the price
Woodworking Supplies S/E QLD - Silverglide Dry Slip
still, a little does go a long way.Apologies for unnoticed autocomplete errors.
-
3rd February 2016, 04:46 PM #5GOLD MEMBER
- Join Date
- Apr 2011
- Location
- McBride BC Canada
- Posts
- 3,543
I was the keeper of a 12" contractors TS. Scribble the decks with the butt of a candle = good to go.
-
3rd February 2016, 08:04 PM #6Novice
- Join Date
- Jan 2009
- Location
- melbourne
- Posts
- 12
Miniwax finishing paste wax has always worked well for me, avaliable at masters
Sent from my iPhone using Tapatalk
-
3rd February 2016, 09:03 PM #7
I'm with Chesand and use this one. Makes the surface slippery and helps stop rust on cast iron surfaces.
-
3rd February 2016, 09:13 PM #8GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 2,685
I've been using Gilly Stevenson floor wax on my cast iron surfaces, for no other reason than I had some and I knew silcone was a no-no. Hope this is OK to use.
Geoff
The view from home
-
3rd February 2016, 10:24 PM #9
+1 for ubeaut traditional wax. Been using the same pot now for 18 months ... Jointer, thicknesser, table saw, level riders on the caravan ... [emoji1]
Glenn Visca
-
3rd February 2016, 10:54 PM #10Senior Member
- Join Date
- Apr 2012
- Location
- Melbourne
- Posts
- 293
I've tried several different ones
WD40 - Excellent for cleaning rust spots (combined with fine grit sandpaper) creates smooth surface...but no long term rust protection or any timber lubrication (I generally use wd40 for initial cleanup)
Teflon spray (bought at masters) - not bad... leaves dull looking film on the surface.. once dried provides good surface protection and wood glide
T9 - Bought from bicycle shop. Provides decent prevention and gliding.. doesn't last as long as other products (in terms of how often it is required to reapply)
Silveglide (slibergleit) - Carbatec... Bit pricey but small amount goes a long way... Bought it on special and not regreting it.. At the moment preffered protection / lubrication medium.. Very easy to apply and last a long time before re-application is required.....
Wax stick - Good protection and wood glide.. but fair bit of elbow grease was required to buff it in (don't have buffer so had to rub it manually) Good on small surfaces otherwise you either going to be master in wax goes on / wax goes off method.. or will really look into investing for a buffer..
-
4th February 2016, 09:52 PM #11Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
+1 for normal candle wax
You work up a sweat buffing it, but it doesn't take very long to do - the 500mm x 500mm table on the bobbin sander takes me no more than 5 mins, ditto for the bandsaw.
I don't know if it's location or the quality of the metal (or a bit of both), but I have never seen a spot of rust on any of the 3 table saws at work (or the spindle moulder, or the buzzer)
They've never been waxed or treated in any way other than the occasional scribble with a candle for lubrication.
Similar Threads
-
Oiling and Waxing
By 27saxophone in forum FINISHINGReplies: 2Last Post: 14th March 2010, 10:34 AM -
Waxing the ways
By petersemple in forum WOODTURNING - GENERALReplies: 12Last Post: 10th May 2008, 01:02 AM -
Waxing one's table saw...
By L G Cooper in forum TABLE SAWS & COMBINATIONSReplies: 5Last Post: 3rd February 2008, 10:42 PM -
Waxing over oil
By Dion in forum FINISHINGReplies: 3Last Post: 21st October 2002, 06:44 PM -
Waxing.
By Shane Watson in forum FINISHINGReplies: 0Last Post: 24th June 2001, 12:50 PM