Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
-
19th February 2011, 10:02 AM #1New Member
- Join Date
- May 2010
- Location
- Sydney, Australia
- Posts
- 6
Panel Saw with Scribe blade, ripping and docking arm.
Hi guys,
I'm looking at buying at panel/table saw with the above features and was wondering if any of you had good advice as to which is the best make & model for a limited budget.
I currently make musical instruments out of ply (1200x2400 sheets) which is why I've been recommended the scribe blade just so the delicate ply doesn't shred on the underside. I've also been told that, for my purposes, a GOOD (accurate) ripping arm is the key, as well as a good docking arm.
I know it's a big ask but my budget is approx. $2,000 but could extend it to $4,000 if I really have to.
Have had a look at the Hare & Forbes, as well as Carbatech but can anyone offer any suggestions as to where I might start to look, or which are the better options?
Cheers in advance for your help.
Regards,
Rod
-
19th February 2011 10:02 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
19th February 2011, 01:29 PM #2Member
- Join Date
- May 2009
- Location
- Geraldton
- Posts
- 71
Hi Rod,
Just a couple of questions,
How big an operation do you need to cater for?
How much space do you have?
If you don't need to cut more than a few sheets a day it might be worth starting with a festool plunge saw. These a like a regular hand held circular saw but they run on tracks. They give a very good quality cut and don't take up any permanent space. Other brands sell cheaper versions but I have only used. If you need to go with a table saw I wouldnt worry about a scribe saw for ply as with a suitable blade and a zero tolerance insert high quality cuts are achievable.
Hope this helps
Ben
-
19th February 2011, 02:40 PM #3New Member
- Join Date
- May 2010
- Location
- Sydney, Australia
- Posts
- 6
Hi Ben,
Yeh I don't have to cut that many sheets, lets say 10 to 20 per month, but this will definitely increase. The guy that is cutting my wood at the moment is very up and down and I have to wait for him to do all his work before he looks at mine...which can sometimes be inconvenient, hence me looking at buying my own.
Space is limited so was looking a moving into a bigger space.
The ply I'm cutting is birch ply which can be very temperamental which is why I was looking at a scribe blade.
Ideally I'd like something that required minimal setup each time I used the machine that's all. I need to get my production times down as much as possible because apart from constructing, I also need to market these instruments, which takes as much time, if not more, than the construction phase of the operation.
Cheers,
Rod
-
19th February 2011, 09:31 PM #4Senior Member
- Join Date
- Apr 2010
- Location
- Australia
- Posts
- 210
Just a philosophical point.
What percentage of your total build time is taken up in sawing? If you had to cut rough and then use a normal table saw to simply trim the edge (or even a router jig) still what percent of the total build would that occupy?
I ask because so often we (yes WE ) ask a tool to save us time, when it only takes up a tiny amount of the total purchase, store, fit, finish etc procedures involved.Nick
Similar Threads
-
Is ripping with a crosscut blade possible?
By SteveMcM in forum TABLE SAWS & COMBINATIONSReplies: 8Last Post: 10th April 2008, 09:36 AM -
Panel Saw Blade Guard
By Cutting Edge in forum TABLE SAWS & COMBINATIONSReplies: 3Last Post: 4th March 2008, 01:54 PM -
Chainsaw ripping blade... but not a rip cut?
By Dean in forum WOODWORK - GENERALReplies: 30Last Post: 23rd February 2007, 12:37 PM -
Ripping Blade
By blindbambi in forum HAND TOOLS - POWEREDReplies: 3Last Post: 13th October 2003, 03:14 PM -
ripping blade
By PeteW in forum TRITON / GMCReplies: 5Last Post: 20th December 2002, 08:46 AM