Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
13th February 2014, 12:25 PM #1New Member
- Join Date
- Feb 2014
- Location
- NZ
- Posts
- 8
Ryobi ETS1526AL - Horizontal blade adjustment
I purchased one of these cheaper table saws a few years ago at bunnings.
I've just noticed the blade alignment is out horizontally - ie, it doesn't run parallel to the rip fence, or the rest of the table top.
Does any one know if this is adjustable? I know you can adjust the vertical angle, but can't see anything in the manual about the horizontal angle.
Thanks
Dave
-
13th February 2014 12:25 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
8th February 2015, 04:36 PM #2New Member
- Join Date
- Feb 2015
- Location
- Auckland
- Posts
- 1
-
8th February 2015, 06:03 PM #3
PROVIDED you can get the blade to run parallel to the mitre slot, the fence can be shimmed (or fit a false face) so that it is parallel to the blade
regards from Alberta, Canada
ian
-
11th February 2015, 11:16 PM #4
I had an older version of that saw with a metal body. It had the trunion assembly suspended under the table by 2 bolts. Slacken the bolts a bit and the whole trunion can be scewed slightly side to side so as the blade is aligned with the miter slot on the table. This is the first and most important adjustment. After that align the fence with the blade. Google table saw setup. The same principles apply to all table saws. I had a look at the manual for your saw and it does not mention this so have a look at how the trunion is attached under the table top. You may have to tip the saw upside down and remove any base plate to see the arrangement. If not sure take some pics and we can have a think of where to go from there.
Regards
John
-
1st April 2015, 07:07 AM #5New Member
- Join Date
- Feb 2014
- Location
- NZ
- Posts
- 8
Hey, only just saw your reply now - (thread is like a year old so I'd given up =)
I've had a pretty damned good poke around under the saw and can't see anywhere obvious that I can adjust it. (But I easily could be overlooking something obvious!). Can you see any likely suspects in the pics below?
Thanks!
Dave
20150331_202440.jpg20150331_202539.jpg
-
1st April 2015, 10:00 AM #6
Judging by your second photo it appears that there are some phillips head screws holding the table to the main blue body and 4 capscrews holding the trunnion to the table. It may be that you can loosen the capscrews and move the trunnion around a bit, but it appears that it may be also attached in some way to the casing where the tilt adjustment is done. If this is the case, you my need to loosen the phillips heads screws holding the table as well and use the combination of the 2 to get the movement you need.
I don't have one of these so I am just going by what I can see in the photos.
You might want to have a look through this thread as well https://www.woodworkforums.com/f153/help-ryobi-ets1526al-blade-miter-gauge-alignment-122034
-
2nd April 2015, 08:50 AM #7New Member
- Join Date
- Feb 2014
- Location
- NZ
- Posts
- 8
So, an update - after pretty much dismantling the damned thing completely yesterday with the aim of following the advice in the other thread of trying to shift the table top, I discovered the motor is fixed in place in relation to the tabletop via a groove in the table top that sits into a bolt (red marks in photo) - so no oppurtunity for movement there.
There's 4 hex bolts holding this plate in place in relation to the tabletop so figure that's what needs to be moved. There's no slack space around the bolts, but figure I might be able to drill out a mm on each to get a bit of clearance... but of course there is zero access to the hex bolts. I can see them through the gears for raising/lowering the saw, but damned if I can work out how to get to them =/
guess I'll have another play over the weekend but suspect this saw might be making a short trip to the dump!
20150401_190926.jpg
-
17th April 2016, 09:36 PM #8New Member
- Join Date
- Apr 2016
- Location
- Uk
- Age
- 72
- Posts
- 1
G,DAY Ijoined this site as I have just bought a used one of these saws and have spent the last 2 days taking it apart to try and rectify this problem! I can confirm their really is no way to cure it I managed to get the blade straight with the table but as soon as I wind the blade up past about 1 1/2 inches it suddenly veers off to the right and eventually hits the useless table insert. You can make the parallel guide adjustable by placing a small shim between the two bolts on the arm then tightening or loosening either bolt moves arm in that direction, mitre gauge also rocks in groove!! I noticed on the excellent photos that threaded rod for height adjustment appears to have 2 circuits on it, mine doesn't anyone know what they do? Many thanks for reading , any advice very welcome
Similar Threads
-
horizontal/vertical bandsaw adjustment..
By Corgan in forum METALWORK FORUMReplies: 19Last Post: 18th August 2011, 09:56 PM -
help! : RYOBI ETS1526AL blade and miter gauge alignment
By baeltus in forum TABLE SAWS & COMBINATIONSReplies: 5Last Post: 18th August 2010, 08:50 PM -
Ryobi ETS1526AL is it worth it?
By Cub in forum TABLE SAWS & COMBINATIONSReplies: 7Last Post: 12th August 2009, 05:09 PM -
Rip Fence Straightener (Ryobi ETS1526AL)
By RedShirtGuy in forum TABLE SAWS & COMBINATIONSReplies: 0Last Post: 20th January 2009, 09:58 PM -
Stanley #71 Blade adjustment
By silentC in forum HAND TOOLS - UNPOWEREDReplies: 6Last Post: 11th May 2007, 10:38 PM