Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 16
Thread: Jointer maintenance
-
9th August 2004, 01:55 AM #1Intermediate Member
- Join Date
- Feb 2003
- Location
- Adelaide, S Aust
- Posts
- 32
Jointer maintenance
Hi Guys,
I've just purchased a jointer. Whats the best way of maintaining the table?
Particularly to prevent rust etc.
Thanks
-
9th August 2004 01:55 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
9th August 2004, 09:30 AM #2
Do a search on 'rust' for heaps of information on this subject.
I wipe my tables down and apply Ubeaut Traditional Wax to them and have never had a rust problem."I don't practice what I preach because I'm not the kind of person I'm preaching to."
-
9th August 2004, 09:47 AM #3
try the product called top-cote. It's designed for exactly what you are looking for: I've found it works great.
http://www.leevalley.com/wood/page.a...=1,43415,43440
-ryan
-
9th August 2004, 06:22 PM #4
Be careful if you use your jointer to prepare edges for glueups and have freshly prepared the table with paste wax as the wax will end up on your timber for the first few passes and could degrade the glue adhesion. It keeps the rust at bay though.
I like cats but I couldn't eat a whole one :
-
9th August 2004, 10:13 PM #5Intermediate Member
- Join Date
- Feb 2003
- Location
- Adelaide, S Aust
- Posts
- 32
Thats exactly what I was worried about. I didn't want to apply something to the table that would come off onto the wood and interfere with either gluing or staining.
Ryan - that spray sounds pretty good. But is it available in Australia? Does it come under a different name? Whats the ingredients?
I could order it from Lee Valley but I also thought that you could not send pressurised cans by airmail. In case it explodes.
Has anyone come in contact with this Top cote in Australia?
-
10th August 2004, 08:55 AM #6degrade the glue adhesion
Anything you put on the table, including Top Cote, is going to come off eventually as you slide timber over it, otherwise you'd never need to replace it. Where do you suppose it ends up?"I don't practice what I preach because I'm not the kind of person I'm preaching to."
-
10th August 2004, 09:32 AM #7Intermediate Member
- Join Date
- May 2004
- Location
- Ringwood
- Age
- 63
- Posts
- 42
How things have changed. I would never of thought you would have to spray the table of a jointer. I have used them for years and have never done that, but then these are commercial units. The tables now must be made out of a low quality steel.
Daniel
-
10th August 2004, 09:42 AM #8
There's two reasons for doing it. The first is that it helps prevent rust. Anything that contains iron will rust under the right conditions. The tables on all of my machines, with the exception of the thicknesser, are made from cast iron. I live a stone's throw from the ocean and if I didn't put wax on them, they'd have a layer of rust on them within a couple of hours.
The second reason is that it reduces friction. After polishing the tables with wax, the timber glides along like it's on wheels.
If you're talking about commercial machinery like you'd find in a joinery, then that is a different story but you'll find that most people asking questions on this forum have their own machines at home and the tables will be cast, not steel."I don't practice what I preach because I'm not the kind of person I'm preaching to."
-
11th August 2004, 08:42 PM #9
.........AND I'm not sure how far from the salt laden air Silent is, but my machinery is about 15 metres (as the midge flies) from the water's edge, so any metal that gets left out for more than about a week ends up with a flat brown dusty cover.
I find the magic "Silverglide" applied with a green scourer and buffed lasts 6 months between applications.
Cheers,
P
-
12th August 2004, 12:46 AM #10Intermediate Member
- Join Date
- Feb 2003
- Location
- Adelaide, S Aust
- Posts
- 32
Whats the "Silverglide"? Where can you get it?
-
12th August 2004, 01:20 AM #11
A product that is readily available in Australia and is used to prevent rust on machines and lubricate tight stuff by some machinary suppliers that I know is called " INOX". It is in an aerosol, just wipe the jointer table before use although I've never had a problem
-
12th August 2004, 02:51 AM #12
I have used a polish made of 50/50 paraffin wax and gum turpentine.
It is really a wood polish but when used on my planner tables it gave me a nice slippery non-marking surface.
After 18 months there is no hint of corrosion and it has a real nice eucalyptus smell.
-
12th August 2004, 03:13 AM #13
OK Polaris - where do I get this polish.
Apart from my cast aluminum saw tables I can get a rust finish in no time. Guess that's the problem living in paradise with ocean views - well someone has to do it!!!
Might be different in Isa though - see other post.
I've tried candle wax and numerous polishes/lubricants without being happy with any really - even tried the cardboard table template sprayed with WD40 style moisture repellant and still I have to get out the steel wool to clean things upPerhaps it is better to be irresponsible and right, than to be responsible and wrong.
Winston Churchill
-
12th August 2004, 10:59 AM #14
Made the polish myself using materials from Bunnies, I had to warm the paraffin wax up to liquidfy it before mixing.
-
12th August 2004, 11:12 AM #15Originally Posted by Sasha
Carbatec sell it in Sydney. I imagine that MIK would sell it in Adelaide.