Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
-
19th May 2023, 02:41 AM #1Senior Member
- Join Date
- Nov 2017
- Location
- Melbourne
- Age
- 73
- Posts
- 358
Should Sherwood bench top jointer outfeed table be level?
I'm debating whether to stick with my bargain basement Aldi combination thicknesser / jointer or buy some supposedly better machines. One of the things I don't like about my Aldi machine is that the outfeed table drops about a millimetre from the cutter to the end of the table, which suggests to me that there's a risk of an uneven shave as it rocks between the cutter height and the end of the table. But it looks like the same thing happens with the Sherwood, as shown in this video at 2.47 minutes https://www.timbecon.com.au/sherwood...ch-top-jointer . Is this the standard set up for out feed tables or is the Sherwood no better than my machine in that respect?
-
19th May 2023 02:41 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
19th May 2023, 07:36 AM #2
That is not the standard set up for jointers. The infeed and outfeed tables should be parallel. Especially over that short distance.
I have zero faith in Timbecons product knowledge and not a lot more in Sherwood quality.
There are many threads here about Timbecons response to not fit for purpose, brand new machinery.Those were the droids I was looking for.
https://autoblastgates.com.au
-
19th May 2023, 09:37 AM #3SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Warragul
- Age
- 68
- Posts
- 577
Yes they've had complaints but I think that's a bit overly harsh. I don't own their jointer but I do own a few of their other machines and they work fine and have been reliable, particularly their thicknesser which I found great value. I'm a hobbyist but maybe a professional woodworker might need something a bit more up market
-
19th May 2023, 10:03 AM #4Senior Member
- Join Date
- Nov 2017
- Location
- Melbourne
- Age
- 73
- Posts
- 358
Thanks for that, which confirms some of the threads I've seen about Timbecon products. Turns out that my crappy little Aldi isn't any worse than the Sherwood one; is a lot cheaper; and it has thicknesser as well that works fine.
Timbecon poor product quality on brand new items goes beyond machinery to simple tools. See my post at Problem with Timbecon Torquata heavy duty pipe clamps
Do you have an opinion on Carbatec bench jointers? Are they any better than Timbecon? Thanks for any advice.
-
19th May 2023, 10:11 AM #5Senior Member
- Join Date
- Nov 2017
- Location
- Melbourne
- Age
- 73
- Posts
- 358
-
19th May 2023, 07:43 PM #6
The infeed and outfeed tables should be adjustable. The hinges are usually able to be lifted up and down until they are level with the plattern and the back of the tables usually have a line of screws with locknuts to increase or decrease the “angle” they sit at; in an ideal world this would be 180 degrees but in reality a couple of degrees less is actually better because the tables flex in use. But if you’re stuck you can make a new sub-table out of formply; long enough so it overlaps the table ends and is held in place by a cleat at each end. Formply has a fairly slippery coating anyway and waxing it will help heaps.If you want to replace it consider the Carbatec TH-BX330P. I have one and for a budget lunchbox thicknesser it’s great; but be warned it’s bloody heavy. Also; they insist on describing it as a spiral head… IT ISN’T. It is a segmented head.
Nothing succeeds like a budgie without a beak.
Similar Threads
-
What is acceptable tolerance on infeed / outfeed tables on jointer?
By 419 in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 4Last Post: 17th May 2023, 12:51 AM -
Work Bench/Outfeed table
By garfield in forum WOODWORK - GENERALReplies: 7Last Post: 14th August 2021, 09:54 PM -
jointer outfeed table adjustment problem
By old_picker in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 4Last Post: 26th June 2015, 07:31 PM -
Outfeed Table
By John Samuel in forum TABLE SAWS & COMBINATIONSReplies: 22Last Post: 30th May 2013, 11:00 PM -
Brand New Jointer - Outfeed Table "Stuck"
By jackliveshere in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 12Last Post: 30th September 2008, 03:13 PM