Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
Thread: Hammer A3-31 Guard
-
20th June 2021, 11:55 AM #1
Hammer A3-31 Guard
The supplied guard often gets in the way of moving your body freely from infeed to outfeed. It is dangerously tempting just to remove the guard completely. I remember seeing this homemade guard somewhere on the net so I easily made one from scrap. I highly recommend it for all Hammer combo owners. As it is much shorter than the supplied guard it can cover exposed cutter head whilst not protruding out the side for most situations. Where only a very small area of cutter head or no cutter head needs to be exposed the original equipment guard can be used.
Mat
-
20th June 2021 11:55 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
20th June 2021, 12:30 PM #2
Hi Mat
I do not get this. When jointing a wide board, the guard covers the full width of the bed. The board passes under the guard. No need to pull it back.
It is only when edge jointing that one pulls the guard back. If the fence remains at the far end, the opening is no more than an inch or two. If the fence is moved into the centre of the bed (so as not to over use one spot on the blade), then there is a reason for a shorter guard ... but this is a small part of the time use with this machine. I would rather put up with a slightly longer guard sticking out for a short period than swap back-and-forth between two guards. Can you explain more about the rationale for a shorter guard.
Photos to illustrate the guard and bed relationship ..
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
20th June 2021, 12:48 PM #3GOLD MEMBER
- Join Date
- Nov 2018
- Location
- Newcastle
- Posts
- 1,016
I think Mat means it pokes you in your chubby little belly when you retract it to process bigger bits of wood.
This is Felder's official solution (a reassuringly pricey option of course):
Screen Shot 2021-06-20 at 11.47.22.jpg
-
20th June 2021, 02:14 PM #4
Derek
Yes mainly an issue with edge jointing but for me this can be up to 100mm. Also to share the wear I don’t always use the far end. If the fence comes forward the guard comes out further. Also for me I have the combo due to reduced space, I don’t have huge amounts of room to move. But most importantly I can move in a straight line from infeed to outfeed as I have been used to on previous jointers without the semicircular movement around the guard. More of a hassle with large boards.
There are also times when the thickness of the board does not allow the guard to stay overhead even jointing the first surface.
Similar Threads
-
WANTED:VIC Triton Workcentre 2000 - Guard support (metal thing the plastic saw guard attaches to
By mookschank in forum WANTED & WANTED TO BUY - in AustraliaReplies: 2Last Post: 25th March 2020, 05:36 PM -
Hammer Slider Overhead Guard
By Chris Parks in forum TABLE SAWS & COMBINATIONSReplies: 0Last Post: 16th March 2015, 08:52 PM -
The Guard.
By Robthechisel in forum WOODCARVING AND SCULPTUREReplies: 5Last Post: 12th June 2014, 01:54 PM -
Wanted: guard support and overhead guard triton saw bench.
By guerd87 in forum TRITON / GMCReplies: 1Last Post: 17th February 2014, 10:55 AM -
Impact Hammer vs Rotary Hammer Drill
By Burnsy in forum HAND TOOLS - POWEREDReplies: 10Last Post: 17th October 2007, 12:22 AM